双时效处理对15-5PH不锈钢强度-韧性的改善

doi:10.1007/s12204-021-2390-5

摘要/Abstract

摘要： 为了获得15-5PH不锈钢更好的强度-韧性匹配，采用双时效处理方法研究了15-5PH不锈钢的力学性能和组织演变。在本研究中，Cu析出相和逆变奥氏体对强度-韧性匹配的改善起着决定性作用。采用电子背散射衍射、透射电镜术和扫描透射电镜术对其微观结构进行了观察。分别采用Thermo-Calc软件和X射线衍射计算并测量Cu析出相和逆变奥氏体的体积分数。结果表明，逆变奥氏体在马氏体板条边界处形成，其体积分数也随着时效温度的增加而增加，同时，Cu析出相的尺寸也逐渐增大。双时效处理与传统的单时效处理相比，15-5PH不锈钢的双时效处理可以在保持必要强度的同时提高韧性。15-5PH不锈钢在550 ℃ × 4 h + 580 ℃ × 1 h的双时效处理中，具有最佳的强度和低温（? 40 ℃）韧性匹配，其屈服强度为1.037 GPa，抗拉强度为1.086 GPa，低温（? 40 ℃）冲击功为179 J。

关键词: 不锈钢, 双时效处理, Cu析出相, 逆变奥氏体, 扫描透射电子显微镜术

Abstract: To obtain better strength-toughness balance of 15-5PH stainless steel, a double aging treatment is proposed to investigate the mechanical properties and microstructure evolution. In this study, Cu precipitates and reversed austenite played a determining role to improve strength-toughness combination. The microstructure was observed using electron backscattered diffraction, transmission electron microscopy and scanning transmission electron microscopy. The volume fractions of Cu precipitates and reversed austenite were calculated with Thermo-Calc software and measured by X-ray diffraction. The results showed that the reversed austenite is formed at the martensitic lath boundaries and its volume fraction also increases with the increase of the aging temperature. At the same time, the size of the Cu precipitates gradually increases. Compared with the traditional single aging and double aging treatment, double aging treatment of 15-5PH stainless steel can increase the toughness while retaining the necessary strength. During double aging of 550 ℃ × 4 h + 580 ℃ × 1 h, 15-5PH stainless steel has the best strength and low-temperature (- 40 ℃) toughness match. Its yield strength, ultimate tensile strength and the Charpy impact energy are 1.037 GPa, 1.086 GPa and 179 J, respectively.

中图分类号:

TG 111.5

特日格乐, 张玉妥, . 双时效处理对15-5PH不锈钢强度-韧性的改善[J]. J Shanghai Jiaotong Univ Sci, 2023, 28(2): 270-279.

TE Rigele (特日格乐), ZHANG Yutuo, ∗ (张玉妥). Strength-Toughness Improvement of 15-5PH Stainless Steel by Double Aging Treatment[J]. J Shanghai Jiaotong Univ Sci, 2023, 28(2): 270-279.

参考文献 23

[1]	AGHAIE-KHAFRI M, MOUSAVI ANIJDAN S H, AMIRKAMALI M. Microstructural evolution under ausforming and aging conditions in 17-4 PH stainless steel [J]. Materials Research Express, 2019, 6(10): 106532.
[2]	COUTURIER L, DE GEUSER F, DESCOINS M, et al. Evolution of the microstructure of a 15-5PH martensitic stainless steel during precipitation hardening heat treatment [J]. Materials & Design, 2016, 107: 416-425.
[3]	MURR L E, MARTINEZ E, HERNANDEZ J, et al. Microstructures and properties of 17-4 PH stainless steel fabricated by selective laser melting [J]. Journal of Materials Research and Technology, 2012, 1(3): 167-177.
[4]	MURAYAMA M, HONO K, KATAYAMA Y. Microstructural evolution in a 17-4 PH stainless steel after aging at 400 ?C [J]. Metallurgical and Materials Transactions A, 1999, 30(2): 345-353.
[5]	HAN G, XIE Z J, LI Z Y, et al. Evolution of crystal structure of Cu precipitates in a low carbon steel [J]. Materials & Design, 2017, 135: 92-101.
[6]	YELI G M, AUGER M A, WILFORD K, et al. Sequential nucleation of phases in a 17-4PH steel: Microstructural characterisation and mechanical properties [J]. Acta Materialia, 2017, 125: 38-49.
[7]	PARK E S, YOO D K, SUNG J H, et al. Formation of reversed austenite during tempering of 14Cr-7Ni-0.3Nb-0.7Mo-0.03C super martensitic stainless steel [J]. Metals and Materials International, 2004, 10(6): 521-525.
[8]	YE D, LI J, JIANG W, et al. Formation of reversed austenite in high temperature tempering process and its effect on mechanical properties of Cr15 super martensitic stainless steel alloyed with copper [J]. Steel Research International, 2013, 84(4): 395-401.
[9]	BHAMBROO R, ROYCHOWDHURY S, KAIN V, et al. Effect of reverted austenite on mechanical properties of precipitation hardenable 17-4 stainlesssteel [J]. Materials Science and Engineering A, 2013, 568: 127-133.
[10]	MAN C, DONG C F, KONG D C, et al. Beneficial effect of reversed austenite on the intergranular corrosion resistance of martensitic stainless steel [J]. Corrosion Science, 2019, 151: 108-121.
[11]	FAN Y H, ZHANG B, YI H L, et al. The role of reversed austenite in hydrogen embrittlement fracture of S41500 martensitic stainless steel [J]. Acta Materialia, 2017, 139: 188-195.
[12]	SONG Y Y, LI X Y, RONG L J, et al. Reversed austenite in 0Cr13Ni4Mo martensitic stainless steels [J]. Materials Chemistry and Physics, 2014, 143(2): 728-734.
[13]	ZHOU T, PRASATH BABU R, ODQVIST J, et al. Quantitative electron microscopy and physically based modelling of Cu precipitation in precipitation-hardening martensitic stainless steel 15-5 PH [J]. Materials & Design, 2018, 143: 141-149.
[14]	HABIBI BAJGUIRANI H R. The effect of ageing upon the microstructure and mechanical properties of type 15-5 PH stainless steel [J]. Materials Science and Engineering A, 2002, 338(1/2): 142-159.
[15]	SUN Y W, ZHONG Y P, WANG L S. The interaction between ε-copper and dislocation in a high copper 17-4PH steel [J]. Materials Science and Engineering A, 2019, 756: 319-327.
[16]	NIU M C, ZHOU G, WANG W, et al. Precipitate evolution and strengthening behavior during aging process in a 2.5 GPa grade maraging steel [J]. Acta Materialia, 2019, 179: 296-307.
[17]	CHEN J, LV M Y, TANG S, et al. Influence of cooling paths on microstructural characteristics and precipitation behaviors in a low carbon V-Ti microalloyed steel [J]. Materials Science and Engineering A, 2014, 594: 389-393.
[18]	YEN H W, CHEN P Y, HUANG C Y, et al. Interphase precipitation of nanometer-sized carbides in a titanium-molybdenum-bearing low-carbon steel [J]. Acta Materialia, 2011, 59(16): 6264-6274.
[19]	LI Z T, CHAI F, YANG L, et al. Mechanical properties and nanoparticles precipitation behavior of multicomponent ultra high strength steel [J]. Materials & Design, 2020, 191: 108637.
[20]	ZHANG C Y, WANG Q F, REN J X, et al. Effect of microstructure on the strength of 25CrMo48V martensitic steel tempered at different temperature and time [J]. Materials & Design, 2012, 36: 220-226.
[21]	LIU H H, FU P X, LIU H W, et al. Effect of vanadium micro-alloying on the microstructure evolution and mechanical properties of 718H pre-hardened mold steel [J]. Journal of Materials Science & Technology, 2019, 35(11): 2526-2536.
[22]	SUN J, WEI S T, LU S P. Influence of vanadium content on the precipitation evolution and mechanical properties of high-strength Fe-Cr-Ni-Mo weld metal [J]. Materials Science and Engineering A, 2020, 772: 138739.
[23]	KAMIKAWA N, SATO K, MIYAMOTO G, et al. Stress-strain behavior of ferrite and bainite with nanoprecipitation in low carbon steels [J]. Acta Materialia, 2015, 83: 383-396.