Formability of AZ31B Magnesium Alloy Sheet Under
 Different Die Temperatures

doi:10.16183/j.cnki.jsjtu.2018.09.013

Abstract

Abstract: To investigate the effect of die temperature on formability of AZ31B magnesium alloy sheet in stamping, forming limit curve (FLC) of AZ31B magnesium alloy sheet was obtained through Nakazima semispherical drawing under different die temperatures. Thermo-mechanical coupling effect under heat transfer between AZ31B magnesium alloy sheet and die was analyzed based on temperature fields of biaxial tension specimens obtained by thermo-mechanical coupled simulation using finite element method. Effect of die temperature on forming limit of AZ31B alloy sheet in working condition was finally verified in a tryout stamping of hinge cover. The results show that temperature gradient distribution of AZ31B magnesium alloy is highly changed with the decline of die temperature, forming limit is thus decreased and fracture position is also affected. The FLCs under different die temperatures are proved to be in good agreement with actual stamping of AZ31B alloy sheet.

Key words: magnesium alloy, warm forming, die temperature, forming limit curve (FLC), finite element method

CLC Number:

TG 386

WANG Zimin,LIU Qi,GU Ruiying,WANG Wurong,WEI Xicheng. Formability of AZ31B Magnesium Alloy Sheet Under Different Die Temperatures[J]. Journal of Shanghai Jiaotong University, 2018, 52(9): 1092-1097.

References

［1］高双. 冷冲压镁合金板材成型工艺及性能研究［D］. 沈阳: 沈阳工业大学机械工程学院, 2014. GAO Shuang. Research on cold stamping process and performance of magnesium alloy sheets［D］. Shen-yang: School of Mechanical Engineering, Shenyang University of Technology, 2014. ［2］刘光晓. AZ31镁合金板材高温成形极限图的理论获取［D］. 长春: 吉林大学机械工程学院, 2013. LIU Guangxiao. AZ31 magnesium alloy sheet high temperature forming limit diagram theory to obtain［D］. Changchun: School of Mechanical Engineering, Jilin University, 2013. ［3］ZHOU G, JAIN M K, WU P, et al. Experiment and crystal plasticity analysis on plastic deformation of AZ31B Mg alloy sheet under intermediate temperatures: How deformation mechanisms evolve［J］. International Journal of Plasticity, 2016, 79(4): 19-47. ［4］李文娟. AZ31B镁合金板料成形性能研究［D］. 济南: 山东大学机械工程学院, 2012. LI Wenjuan. Research on the formability of AZ31B magnesium alloy sheet［D］. Jinan: School of Mechanical Engineering, Shandong University, 2012. ［5］钟敏. AZ31镁合金板材温热成形极限及回弹研究［D］. 上海: 上海交通大学机械与动力工程学院, 2012. ZHONG Min. Research of forming limit and spring-back of magnesium alloy sheet AZ31 at warm condition［D］. Shanghai: School of Mechanical Engineering, Shanghai Jiao Tong University, 2012. ［6］BRUNI C, FORCELLESE A, GABRIELLI F, et al. Effect of temperature, strain rate and fibre orientation on the plastic flow behaviour and formability of AZ31 magnesium alloy［J］. Journal of Materials Processing Technology, 2010, 210(10): 1354-1363. ［7］ZHOU G, ANANTHAESWARA K, MITUKIEWICZ G, et al. FE simulations of gas blow forming and prediction of forming limit diagram of AZ31 magnesium sheet［J］. Journal of Materials Processing Technology, 2015, 218(4): 12-22. ［8］WANG W R, HUANG L, TAO K H, et al. Formability and numerical simulation of AZ31B magnesium alloy sheet in warm stamping process［J］. Materials & Design, 2015, 87(12): 835-844. ［9］TARI D G, WORSWICK M J. Elevated temperature constitutive behavior and simulation of warm forming of AZ31B［J］. Journal of Materials Processing Technology, 2015, 221(7): 40-55. ［10］何燕玲. 镁合金AZ31B板料胀形实验及成形性能研究［D］. 济南: 山东大学机械工程学院, 2012. HE Yanling. Magnesium alloys AZ31B sheet bulging test and the formability research［D］. Jinan: School of Mechanical Engineering, Shandong University, 2012. ［11］YOON J, LEE Y. Fracture mechanism of Mg-3Al-1Zn sheet at the biaxial state with respect to forming temperatures［J］. Materials & Design, 2014, 55(6): 43-49. ［12］WANG L F, HUANG G S, HONG-CHENG L I, et al. Influence of strain rate on microstructure and formability of AZ31B magnesium alloy sheets［J］. Transactions of Nonferrous Metals Society of China, 2013, 23(4): 916-922.

[1]	WANG Rui, HU Zhiping, YIN Ke, MA Jiakuan, REN Xiang. Dynamic Responses Law of Subgrade of a Special Railway Line in Loess Region [J]. Journal of Shanghai Jiao Tong University, 2022, 56(7): 908-918.
[2]	ZHANG Peizhen, LIN Fang. Sound Scattering Characteristics of Oxygen Cylinder for Open Breathing Diver [J]. Journal of Shanghai Jiao Tong University, 2022, 56(6): 764-771.
[3]	MA Zunnong, ZHANG Yansong, ZHAO Yixi. Mechanism and Influencing Factors of Frictional Energy Dissipation in Multilayer Ultrasonic Welding [J]. Journal of Shanghai Jiao Tong University, 2022, 56(6): 772-783.
[4]	LI Yuanhui, LI Jianjun, WANG Shunchao, ZHANG Longyao, ZHU Wenfeng. Modeling and Experiment on Roll-Hemming Forming Process of Aluminum Alloy Sheet with Adhesive [J]. Journal of Shanghai Jiao Tong University, 2022, 56(4): 532-542.
[5]	TANG Genglin, LI Jianjun, LI Yuanhui, ZHANG Longyao, ZHU Wenfeng. Numerical Simulation and Experimental Research of Sheet Hemming Forming Based on Adhesive Filling [J]. Journal of Shanghai Jiao Tong University, 2022, 56(4): 523-531.
[6]	ZHU Hanhao, XIAO Rui, ZHU Jun, TANG Jun. Propagation Characteristics of Low Frequency Sound Energy in Range-Dependent Shallow Water Waveguides [J]. Journal of Shanghai Jiao Tong University, 2021, 55(8): 958-967.
[7]	ZHANG Yu, LIU Haiting, WENG Lin, SHEN Yao. Extraction of Fracture Toughness Parameters by Ring-Notched Small Punch Specimen Using Cohesive Model [J]. Journal of Shanghai Jiao Tong University, 2021, 55(7): 850-857.
[8]	ZHAO Pengfei, XUE Xin, YANG Cheng. Simulation of Influence of End Anchorage Degradation of Stirrups Caused by Alkali Aggregate Reaction on Shear Performance of Reinforced Concrete Beams [J]. Journal of Shanghai Jiao Tong University, 2021, 55(6): 681-688.
[9]	GUO Deping, LI Zheng, PENG Senlin, ZENG Zhikai, WU Daifeng. Numerical Calculation Method for Crack Dynamic Propagation Based on Newmark Implicit Time Integration Scheme [J]. Journal of Shanghai Jiao Tong University, 2021, 55(6): 689-697.
[10]	ZHANG Yuan, LI Fanchun, JIA Dejun. Design and 3D Printing Simulation of a Lattice Compressor Impeller [J]. Journal of Shanghai Jiao Tong University, 2021, 55(6): 729-740.
[11]	ZHOU Bo∗ (周博), KANG Zetian (康泽天), WANG Zhiyong (王志勇), XUE Shifeng (薛世峰). Nonlinear Finite Element Method Considering Martensite Plasticity for Shape Memory Alloy Structure [J]. J Shanghai Jiaotong Univ Sci, 2021, 26(6): 774-785.
[12]	JING Mengjie (荆梦杰), CUI Zhixin(崔志鑫), FU Hang (傅航), CHEN Xiaojun (陈晓军). Real-Time Deformation Simulation of Kidney Surgery Based on Virtual Reality [J]. J Shanghai Jiaotong Univ Sci, 2021, 26(3): 290-297.
[13]	ZHENG Changlong, DING Xiaohong, SHEN Hong, ZHAO Lijuan. Dynamic Topology Optimization of Rudder Structure Based on Adaptive Growth Method [J]. Air & Space Defense, 2021, 4(2): 7-.
[14]	WANG Feng, CHEN Jiali, CHEN Denghong, FAN Yong, LI Zhiyuan, HE Weiping. Element-Free Galerkin Scaled Boundary Method Based on Moving Kriging Interpolation for Steady Heat Conduction Analysis with Temperatures on Side-Faces [J]. Journal of Shanghai Jiao Tong University, 2021, 55(11): 1483-1492.
[15]	JIANG Qianqian,WANG Jiaxu,LI Junyang,XIAO Ke,TANG Ting,WANG Cheng. Influence of Double Circular Arc Harmonic Transmission Profile Parameters on Flexspline Stress [J]. Journal of Shanghai Jiaotong University, 2020, 54(2): 167-175.

Formability of AZ31B Magnesium Alloy Sheet Under Different Die Temperatures

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments