离心式无堵塞泵不等扬程的优化设计与试验

摘要/Abstract

摘要：

摘要：为了使离心式无堵塞泵满足多工况运行的要求，采用不等扬程水力设计方法对模型泵100QW110167.5的叶轮进行优化设计，并结合计算流体力学数值模拟技术分析由原始方案和新方案所得叶轮的内部流场分布，同时，在模拟的基础上对模型样机进行了性能测试.结果表明：采用新方案所得叶轮对流体做功更充分，其流线在不同工况下的分布更均匀、流畅，能够改善泵内流体的流动状况；由新方案所得模型泵在额定流量下的扬程为16.89 m，效率为83.11%，已达到节能级离心式清水泵的产品性能要求，在小流量工况下无马鞍区、振动较小，大流量下高效率区的范围较宽，处于0.8q~1.3q且其无堵塞性能优于原始方案；由新方案所得模型泵性能的预测曲线与试验结果基本吻合，最大误差为7.56%.

关键词: 离心泵, 无堵塞, 扬程, 多工况, 优化设计

Abstract:

Abstract： In order to make non-clogging centrifugal pump meet the requirement of multiple operating conditions, optimization design of the 100QW110167.5 model pump impeller was done by using the unequal head hydraulic design method. Combining with the CFD numerical simulation technology, the internal flow field of the original scheme and new scheme were analyzed. It shows that the new impeller does work more fully, its flow lines distributed more uniformly and smoothly at different conditions, and the flow condition of the pump is improved. Besides, the optimal model prototype, based on the simulation, was tested. And the results show that the head of the model pump is 16.89 m and the efficiency reaches 83.11% at the rated point, which has exceeded energysaving level product requirement of the centrifugal water pump. At low flow conditions, no saddle area and no intense vibration phenomenon occure, meeting the design requirements. The efficiency curve, between 0.8q and 1.3q of its efficient region, has a wide efficient area. And the nonclogging performance is better than the original scheme. The predicted curve is basically consistent with the experimental one, and the maximum error is 7.56%, indicating that the numerical simulation is accurate.

Key words: centrifugal pump, nonclogging, head, multiconditions, optimal design

中图分类号:

TH 311

朱荣生1，邢树兵1，龙云2，王秀礼1，贺博1，曹梁1. 离心式无堵塞泵不等扬程的优化设计与试验[J]. 上海交通大学学报（自然版）, 2015, 49(05): 675-680.

ZHU Rongsheng1,XING Shubing1,LONG Yun2,WANG Xiuli1,HE Bo1,CAO Liang1. Unequal Head Hydraulic Optimal Design and Experiment on a Non-clogging Centrifugal Pump[J]. Journal of Shanghai Jiaotong University, 2015, 49(05): 675-680.

参考文献

［1］Zhao B J, Huang Z F, Chen H L, et al. Numerical investigation of solidliquid two phase flow in a nonclogging centrifugal pump at offdesign conditions ［C］∥ IOP Conference Series: Earth and Environmental Science. UK: IOP Publishing, 2012, 15(6): 19.

［2］Derakhshan S, Pourmahdavi M, Abdolahnejad E, et al. Numerical shape optimization of a centrifugal pump impeller using artificial bee colony algorithm［J］. Computers and Fluids, 2013, 81: 145151.

［3］Nourbakhsh A, Safikhani H, Derakhshan S. The comparison of multiobjective particle swarm optimization and NSGA II algorithm: applications in centrifugal pumps［J］. Engineering Optimization, 2011, 43(10): 10951113.

［4］施卫东, 孙新庆, 陆伟刚, 等. 低比转数潜水电泵无过载设计［J］. 农业机械学报, 2010, 41(7): 3639.

SHI Weidong, SUN Xinqing, LU Weigang, et al. Nonoverload designing research on low specific speed submersible pump［J］. Transactions of the Chinese Society for Agricultural Machinery, 2010, 41(7): 3639.

［5］施卫东, 蒋婷, 曹卫东, 等. 高扬程无过载潜水排污泵的优化设计与试验［J］. 农业工程学报, 2011, 27（5）: 151155.

SHI Weidong, JIANG Ting, CAO Weidong, et al. Optimal design and experiment on a highhead nonoverload submersible sewage pump［J］. Transactions of the Chinese Society of Agricultural Engineering, 2011，27(5): 151155.

［6］Nishi Y, Fujiwara R, Fukutomi J. Design method for singleblade centrifugal pump impeller［J］. Journal of Fluid Science and Technology, 2009, 4(3): 786800.

［7］朱荣生, 胡自强, 付强. 双叶片泵内压力脉动的数值模拟［J］. 农业工程学报, 2010, 26(6):129134, 392.

ZHU Rongsheng, HU Ziqiang, FU Qiang. Numerical simulation of pressure fluctuation in doubleblade pump［J］. Transactions of the Chinese Society of Agricultural Engineering, 2010, 26(6): 129134, 392.

［8］朱荣生, 胡自强, 杨爱玲. 双叶片泵内非定常流动的数值模拟［J］. 排灌机械工程学报, 2011, 29(1): 2630.

ZHU Rongsheng, HU Ziqiang, YANG Ailing. Numerical simulation of unsteady flow in doubleblade pump［J］. Journal of Drainage and Irrigation Machinery Engineering, 2011, 29(1): 2630.

［9］刘厚林, 杨东升, 谈明高, 等. 双叶片离心泵内失速现象的三维PIV分析［J］. 上海交通大学学报, 2012, 46(5): 734739.

LIU Houlin, YANG Dongsheng, TAN Minggao, et al. 3DPIV measurements of stall in doubleblade centrifugal pump ［J］. Journal of Shanghai Jiaotong University, 2012, 46(5): 734739.

［10］Feng J J, Benra F K, Dohmen H J. Unsteady flow visualization at partload conditions of a radial diffuser pump: By PIV and CFD［J］. Journal of Visualization, 2009, 12(1): 6572.

［11］朱荣生. 离心泵叶轮不等扬程水力设计方法研究［D］. 江苏：江苏大学流体机械及工程技术研究中心，2011.

［12］王凯, 刘厚林, 袁寿其, 等. 离心泵多工况水力性能优化设计方法［J］. 排灌机械工程学报, 2012, 30(1): 2024.

WANG Kai, LIU Houlin，YUAN Shouqi, et al. Optimization method for hydraulic performance of centrifugal pump at multioperation［J］. Journal of Drainage and Irrigation Machinery Engineering, 2012, 30(1): 2024.

［13］吴达人.离心泵流体力学［M］.北京:中国电力出版社，1998：827.

［14］HU B, Yuan S Q, Lu W G, et al. Numerical optimal design of a nonoverload centrifugal pump［C］∥ASME 2012 Fluids Engineering Division Summer Meeting. USA: ASME, 2012: 427433.

［15］Lucius A, Brenner G. Numerical simulation and evaluation of velocity fluctuations during rotating stall of a centrifugal pump［J］. Journal of Fluids Engineering, 2011, 133(8):0811020811028.

[1]	李嘉, 李华聪, 王玥. 变汽液比条件下高速燃油离心泵非定常特性分析研究[J]. 上海交通大学学报, 2022, 56(5): 622-634.
[2]	陶威, 刘钊, 许灿, 朱平. 三维正交机织复合材料翼子板多尺度可靠性优化设计[J]. 上海交通大学学报, 2021, 55(5): 615-623.
[3]	谢颉, 张文光, 尹雪乐, 李伟. 基于正交试验方法的柔性神经电极优化设计[J]. 上海交通大学学报, 2020, 54(8): 785-791.
[4]	牟介刚, 章子成, 谷云庆, 施郑赞, 郑水华. 圆形非光滑表面叶片对离心泵空化特性的影响[J]. 上海交通大学学报, 2020, 54(6): 577-583.
[5]	王兰志, 李书新. 一种基于滑动铰点的快速起竖方法及优化设计[J]. 空天防御, 2020, 3(2): 24-28.
[6]	温桠妮, 颜国正, 王志武, 姜萍萍, 薛蓉蓉, 王艺芸. 肠道机器人三维接收线圈的设计与优化[J]. 上海交通大学学报, 2020, 54(11): 1117-1123.
[7]	张科, 吴亚东. 拓宽大涵道比风扇稳定运行范围的叶片优化设计[J]. 上海交通大学学报, 2020, 54(10): 1024-1034.
[8]	龙周, 陈松坤, 王德禹. 基于SMOTE算法的船舶结构可靠性优化设计[J]. 上海交通大学学报, 2019, 53(1): 26-34.
[9]	卫旭敏, 张传荣, 张恩铭, 郭洪, 吴文龙, 张荆柯. 基于ANSYS的短抬梁结构优化设计[J]. 海洋工程装备与技术, 2018, 5(增刊): 149-153.
[10]	倪何，覃海波，金家善，孙丰瑞. 基于差异演化和残差修正的离心泵特性辨识与汽蚀分析[J]. 上海交通大学学报（自然版）, 2018, 52(7): 831-836.
[11]	牟介刚a，吴振兴a，周佩剑a，谷云庆a，吴登昊b，任芸b. 自吸离心泵蜗壳内瞬态流动特性[J]. 上海交通大学学报（自然版）, 2018, 52(4): 461-468.
[12]	程耀楠，韩禹，关睿，徐明，卢真真. 高强钢高效加工层切面铣刀优化设计及仿真分析[J]. 上海交通大学学报（自然版）, 2017, 51(8): 1006-1012.
[13]	何雨辰,葛志强,宋执环 . 基于动态信息的过渡过程辨识方法[J]. 上海交通大学学报（自然版）, 2017, 51(6): 686-692.
[14]	翟国栋, 李明阳. 机械优化设计课程实践教学项目设计[J]. 实验室研究与探索, 2017, 36(5): 178-183.
[15]	孟祥伟, 于玮, 邓欣旺, 张建成, 刘江涛. HYSY201船托管架滚轮组的结构改进[J]. 海洋工程装备与技术, 2017, 4(3): 162-167.