A Review of Sheet Metal Shear Test Methods and Applications

Abstract

Abstract:

Domestic and international research on sheet metal shear tests was reviewed in this paper, in which the tests were divided into three types, that is, multipoint bolt clamping, linear concentrated clamping, and surface uniform clamping, in accordance with the sheet clamping method. The typical devices and samples of each clamping method were introduced. According to the way of clamping force applied, the stress states were analyzed.
Based on the approximation to the simple shear stress state, judgments from different characteristics of the three methods were acquired.

Key words: sheet metal shear test, mechanical property testing, clamping methods, anisotropy

CLC Number:

TG 707

ZHENG Yu,LI Hongye,ZHUANG Xincun,ZHAO Zhen. A Review of Sheet Metal Shear Test Methods and Applications[J]. Journal of Shanghai Jiaotong University, 2014, 48(03): 422-426.

References

［1］Carbonniere J, Thuillier S, Sabourin F, et al. Comparison of the work hardening of metallic sheets in bending–unbending and simple shear［J］. International Journal of Mechanical Sciences, 2009, 51:122130.

［2］王进, 陈军, 张斌, 等. 35CrMo结构钢热塑性变形流动应力模型［J］.上海交通大学学报, 2005, 39(11):17841791.

WANG Jin, CHEN Jun, ZHANG Bin, et al. The flow stress model of 35CrMo structural steel during hot forming［J］. Journal of Shanghai Jiaotong University, 2005, 39(11):17841791.

［3］Rusinek A, Klepaczko J R. Shear testing of a sheet steel at wide range of strain rates and a constitutive relation with strainrate and temperature dependence of the flow stress［J］. International Journal of Plasticity, 2001, 17:87115.

［4］Bouvier S, Gardey B, Haddady H, et al. Characterization of the straininduced plastic anisotropy of rolled sheets by using sequences of simple shear and uniaxial tensile tests［J］. Journal of Materials Processing Technology, 2006, 174:115126.

［5］Thuillier S, Manach P Y. Comparison of the workhardening of metallic sheets using tensile and shear strain paths［J］. International Journal of Plasticity, 2009, 25:733 751.

［6］Rauch E F. Plastic anisotropy of sheet metals determined by simple shear tests［J］. Materials Science and Engineering A, 1998, 241:179 183.

［7］Gasperini M, Pinna C, Swiatnicki S. Microstructure evolution and strain localization during shear deformation of an alluminum alloy［J］. Acta Material, 1996, 44(10):4195 4208.

［8］Peir J, Verleyson P, Van Paepegem W, et al. Determining the stressstrain behavior at large strains from high strain rate ensile and shear experiments［J］. International Journal of Impact Engineering, 2011, 38:406 415.

［9］Yin Q, Soyarslan C, Guner A, et al. A cyclic twin bridge shear test for the identification of kinematic hardening parameter［J］. International Journal of Mechanical Sciences, 2012, 59:31 43.

［10］孔庆瑞, 王家莲. 方形截面试样单剪切试验装置的设计［J］. 工程与试验, 2010(增刊):3940.

KONG Qinrui, WANG Jialian. Design on single shear test for square section specimen［J］. Engineering and Test, 2010(Sup.):3940.

［11］黄小明, 胡世光. 纯剪试验研究［J］. 锻压技术, 1991(5):2124.

HUANG Xiaoming, HU Shiguang. Research of simple shearing test［J］. Forging and Stamping Technology, 1991(5):2124.

[1]	LI Ke1,2,WANG Yingyi3,HUANG Xingchun3. An Evaluation Method and Application of Mechanical Parameters of Fractured Rock Mass [J]. Journal of Shanghai Jiaotong University, 2013, 47(10): 1569-1573.
[2]	LU Jian,CHEN Jun,ZHANG Feifei,CHEN Jieshi. Constitutive Model of Hydroforming and Its Numerical Validation Based on Three-Dimensional Hill’48 Yield Criterion [J]. Journal of Shanghai Jiaotong University, 2013, 47(05): 791-794.
[3]	. The Research of the Anisotropic Fatigue Behavior of 7475 Aluminum Alloy Plate [J]. Journal of Shanghai Jiaotong University, 2011, 45(11): 1678-1683.
[4]	NIU Jianhuia，ZHU Pinga，b，GUO Yongjina . Mechanical Properties of Hotdip Galvanized Dual Phase Steel DP590 and Its Constitutive Model [J]. Journal of Shanghai Jiaotong University, 2010, 44(10): 1382-1387.