中比转速无过载多级离心泵的叶轮设计方法

摘要/Abstract

摘要：

摘要：为达到中比转速多级离心泵无过载性能的要求，在无过载理论的基础上，根据速度系数法推导出新的中比转速多级离心泵叶轮的无过载设计公式，设计了比转速为89.3和135.0的多级泵叶轮，利用Fluent软件进行模拟计算，并与传统公式所设计的泵叶轮进行对比分析.结果表明：在2个设计实例中，采用所推导的公式设计的叶轮轴功率曲线均出现极大值，功率备用系数K分别为1.13和1.03，从而验证了所推导公式的准确性；与采用传统公式相比，采用所推导的公式设计的2种泵的扬程分别提高了14.0%、7.5%，效率分别提高了2.68%、1.03%，而且能够保证较小的径向尺寸；推导的公式较适用于中比转速无过载多级离心泵的叶轮设计.

关键词: 中比转速, 多级, 离心泵, 叶轮, 无过载

Abstract:

Abstract： To meet the demand of the non-overload characteristic of medium specific speed multistage centrifugal pumps, a formula for the design of impeller was derived by using empirical correlations, based on the theory of non-overload. Two pumps, the specific speeds of which were 89.3 and 135.0, were designed using this formula and the traditional formula, and the performance curves were obtained using Fluent. The results indicate that the extreme point of shaft power curve appeares in both of the pumps designed using the derived formula, and the coefficient K, the ratio of the maximal axle power to the power in designed working condition are 1.13 and 1.03, validiting the derived formula. Compared with the pumps designed using the traditional formula, the head of the pumps designed using the derived formula increases by 14.0% and 7.5%, and the efficiency increases by 2.68% and 1.03%. Meanwhile the radial dimension becomes smaller. The derived formulas can be used for medium specific speed non-overload multistage centrifugal pumps.

Key words: medium specific speed, multistage, centrifugal pump, impeller, non-overload

中图分类号:

TH 311

马艺1,2,马中强1,张生昌1,2,张志鸿1,范卫钢3,王金泉3. 中比转速无过载多级离心泵的叶轮设计方法[J]. 上海交通大学学报（自然版）, 2015, 49(05): 695-701.

MA Yi1,2,MA Zhongqiang1,ZHANG Shengchang1,2,ZHANG Zhihong1,FAN Weigang3,WANG Jinquan3. A Novel Design Method for Impeller of Medium Specific Speed Non-Overload Multistage Centrifugal Pumps[J]. Journal of Shanghai Jiaotong University, 2015, 49(05): 695-701.

参考文献

［1］汪家琼，孔繁余. 多级离心泵叶轮与导叶水力性能优化研究［J］.华中科技大学学报:自然科学版, 2013，41(3)：9296.

WANG Jiaqiong, KONG Fanyu. Hydraulic performance optimization study on impeller and diffuser of multistage pump［J］. Journal of Huazhong University of Science and Technology:Natural Science Edition, 2013,41(3): 9296.

［2］袁寿其.低比速离心泵理论与设计［M］.北京：机械工业出版社，1997：68104.

［3］Shi W D，Long F，Li Y, et al. Nonoverload design of low specific speed submersible pump［C］∥ASME 2010 3rd Joint USEuropean Fluids Engineering Summer Meeting and 8th International Conference on Nanochannels, Microchannels, and Minichannels. Montreal, Canada: American Society of Mechanical Engineer, 2010: 563567.

［4］施卫东，李辉，陆伟刚，等. 进口预旋对低比速离心泵无过载性能的影响［J］. 农业机械学报，2013，44(5)：5054, 112.

SHI Weidong, LI Hui, LU Weigang, et al. Effect of prewhirl flow on nonoverload performance of lowspecificspeed centrifugal pumps［J］. Transactions of the Chinese Society for Agricultural Machinery, 2013, 44(5): 5054, 112.

［5］张金凤，沈艳宁，袁寿其，等. 带分流叶片离心泵无过载特性的理论与试验研究［J］. 排灌机械工程学报， 2010, 28(5): 407411, 454.

ZHANG Jinfeng, SHEN Yanning, YUAN Shouqi, et al. Theory and experiment on nonoverload characteristics for centrifugal pump with splitters［J］. Journal of Drainage and Irrigation Machinery Engineering, 2010, 28(5): 407411,454.

［6］杨军虎，郭斌，王玥，等. 无过载离心泵设计参数与性能关系研究［J］. 农业机械学报, 2012, 43(11)： 119122, 128.

YANG Junhu, GUO Bin, WANG Yue, et al. Relationship of performances and design parameters for nonoverload centrifugal pumps［J］. Transactions of the Chinese Society for Agricultural Machinery, 2012, 43(11):119122,128.

［7］司乔瑞，袁寿其，王川，等. 低比速多级潜水泵优化设计［J］. 农业工程学报, 2012, 28(8): 122127.

SI Qiaorui, YUAN Shouqi, WANG Chuan，et al. Optimal design of submersible multistage pumps with low specific speed［J］. Transactions of the Chinese Society of Agricultural Engineering, 2012, 28(8):122127.

［8］张帆，袁寿其，付强，等. 带分流叶片低比转速无过载离心泵优化设计［J］.流体机械，2013，41(6)：1115,21.

ZHANG Fan, YUAN Shouqi, FU Qiang, et al. Nonoverload optimization design on low specific speed centrifugal pump with splitter blades［J］. Fluid Machinery, 2013, 41(6): 1115, 21.

［9］Braun O, Avellan F, Dupont P. Unsteady numerical simulations of the flow related to the unstable energydischarge characteristic of a medium specific speed double suction pump［C］∥ASME/JSME 2007 5th Joint Fluids Engineering Conference. San Diego, California, USA: American Society of Mechanical Engineers, 2007: 971978.

［10］Zhang F, Yuan S Q, Fu Q, et al. Optimization design and inner flow analysis on a mediumhigh specific speed centrifugal pump［C］∥ASME 2013 Fluids Engineering Division Summer Meeting. Incline Village, Nevada, USA: American Society of Mechanical Engineers, 2013: 17.

［11］Hu B, Yuan S Q, Lu W G, et al. Numerical optimal design of a nonoverload centrifugal pump［C］∥ASME 2012 Fluids Engineering Summer Meeting. Rio Grande, Puerto Rico: American Society of Mechanical Engineers, 2012: 427433.

［12］王洋, 刘洁琼, 何文俊. 无过载离心泵结构参数优化设计［J］. 农业工程学报, 2012, 28(3): 3337.

WANG Yang, LIU Jieqiong, HE Wenjun. Parameter optimization of nonoverload centrifugal pump［J］. Transactions of the Chinese Society of Agricultural Engineering, 2012, 28(3): 3337.

［13］刘在伦，李朴蓉. 基于Matlab的泵可用汽蚀余量曲线拟合方法探讨［J］. 流体机械, 2012, 40(7): 4851.

LIU Zailun, LI Purong. Research about fitting approach of pump available NPSH curve based on Matlab［J］. Fluid Machinery, 2012, 40(7): 4851.

［14］关醒凡. 现代泵理论与设计［M］. 北京: 中国宇航出版社, 2011: 254258.

［15］陈芳芳, 李志鹏, 王昌生. 首级叶轮结构对多级泵效率影响的数值模拟［J］. 电站系统工程, 2013, 29(3): 911.

CHEN Fangfang, LI Zhipeng, WANG Changsheng. Numerical simulation of first stage impeller structure influencing efficiency of multistage pumps［J］. Power system Engineering, 2013, 29(3): 911.

［16］孔繁余，宿向辉，陈浩，等. 离心泵径向导叶正叶片参数的优化设计［J］. 农业工程学报, 2012, 28(23): 4045.

KONG Fanyu, SU Xianghui, CHEN Hao, et al. Optimal design on parameters of guide vane of radial diffusers in centrifugal pump［J］. Transactions of the Chinese Society of Agricultural Engineering, 2012, 28(23): 4045.

编辑推荐 0

Metrics

阅读次数

全文

107

HTML			PDF

最新录用	在线预览	正式出版	最新录用	在线预览	正式出版
0	0	0	0	0	107

	来源	其他网站

	次数	107
	比例	100%

摘要

最新录用	在线预览	正式出版

0	0	95

	来源	其他网站

	次数	95
	比例	100%

[1]	李嘉, 李华聪, 王玥. 变汽液比条件下高速燃油离心泵非定常特性分析研究[J]. 上海交通大学学报, 2022, 56(5): 622-634.
[2]	张源, 李范春, 贾德君. 点阵压气机叶轮的设计与3D打印仿真[J]. 上海交通大学学报, 2021, 55(6): 729-740.
[3]	涂壤, 刘孟丹, 王思琪. 转轮辅助空气取水流程优化及性能分析[J]. 上海交通大学学报, 2021, 55(11): 1392-1400.
[4]	杨孙圣, 邵珂, 戴韬. 平行进口叶轮切割对混流泵作透平的影响[J]. 上海交通大学学报, 2020, 54(8): 805-812.
[5]	牟介刚, 章子成, 谷云庆, 施郑赞, 郑水华. 圆形非光滑表面叶片对离心泵空化特性的影响[J]. 上海交通大学学报, 2020, 54(6): 577-583.
[6]	倪何，覃海波，金家善，孙丰瑞. 基于差异演化和残差修正的离心泵特性辨识与汽蚀分析[J]. 上海交通大学学报（自然版）, 2018, 52(7): 831-836.
[7]	牟介刚a，吴振兴a，周佩剑a，谷云庆a，吴登昊b，任芸b. 自吸离心泵蜗壳内瞬态流动特性[J]. 上海交通大学学报（自然版）, 2018, 52(4): 461-468.
[8]	王海燕, 王春升, 张明, 尚超, 孙宏徽, 郑晓鹏. 多级紧凑式气浮工艺处理海上重质油田生产水的研究[J]. 海洋工程装备与技术, 2018, 5(1): 16-19.
[9]	代翠a，董亮b，孔繁余b，柏宇星b，夏斌b. 离心泵作透平倾斜叶片主动降噪[J]. 上海交通大学学报（自然版）, 2016, 50(04): 575-582.
[10]	牟介刚1，代东顺1，谷云庆1，刘剑1，郑水华1，WANG Evan2. 非光滑表面离心泵叶轮的流动减阻特性[J]. 上海交通大学学报（自然版）, 2016, 50(02): 306-312.
[11]	朱荣生1，邢树兵1，龙云2，王秀礼1，贺博1，曹梁1. 离心式无堵塞泵不等扬程的优化设计与试验[J]. 上海交通大学学报（自然版）, 2015, 49(05): 675-680.
[12]	潘潇1,2，王文平1,2，李述林1,2,肖若富3，潘常春4. 离心式燃油泵复合叶轮的数字化设计及验证[J]. 上海交通大学学报（自然版）, 2014, 48(08): 1164-1169.
[13]	张颖，季常刚，李俊甫. 一种基于能量和距离的多级能量异构传感器网络路由算法[J]. 上海交通大学学报（自然版）, 2014, 48(07): 953-958.
[14]	王睿1, 雷红伟1, 彭英武2, 李庆民2, 祁永强1. 战时任务条件下舰艇装备多级备件优化[J]. 上海交通大学学报（自然版）, 2013, 47(03): 398-403.
[15]	刘厚林, 杨东升, 谈明高, 王凯, 庄宿国, 杜辉. 双叶片离心泵内失速现象的三维PIV分析[J]. 上海交通大学学报（自然版）, 2012, 46(05): 734-739.