不同燃烧模式下正庚烷燃烧发动机排气超细颗粒特性

上海交通大学学报（自然版） ›› 2011, Vol. 45 ›› Issue (06): 837-841.

不同燃烧模式下正庚烷燃烧发动机排气超细颗粒特性

刘炜1,2，黄震1

(1.上海交通大学动力机械与工程教育部重点实验室,上海 200240；
2.深圳创新集团投资有限公司博士后工作站,广东深圳 518048)

收稿日期:2010-05-05 出版日期:2011-06-29 发布日期:2011-06-29
基金资助:
教育部高校博士点基金项目(20070248024)

Effects of Combustion Modes on Exhaust Particle Size Distributions from a Diesel Engine Fueled with n-Heptane

LIU Wei-1, 2 , HUANG Zhen-1

( 1. Key Laboratory for Power Machinery and Engineering of Ministry of Education,Shanghai Jiaotong University, Shanghai 200240, China； 2. Postdoctoral Working Station, Shenzhen Capital Group Co., Ltd, Shenzhen 518048, Guangdong, China)

Received:2010-05-05 Online:2011-06-29 Published:2011-06-29

摘要/Abstract

摘要： 在改造的发动机上研究了正庚烷缸内直喷压燃（CIDI）、进气道喷射均质压燃（HCCI）以及进气道气缸喷射复合燃烧（CCCI）3种燃烧模式的发动机排气超细颗粒特性.结果表明，排气超细颗粒数浓度-粒径分布曲线随预混合率变化显著；CIDI燃烧时，排气超细颗粒以积聚模态微粒为主.随着预混合率的增大，排气积聚模态微粒数浓度明显降低,而核模态数浓度则显著增大;正庚烷HCCI燃烧时发动机排气超细颗粒以核模态微粒为主，积聚模态微粒数浓度很低;正庚烷CCCI和HCCI燃烧时发动机排气总颗粒数浓度明显较CIDI燃烧时高.排气核模态数浓度与HC排放明显相关.

关键词: , 燃烧模式, 排气, 超细颗粒, 正庚烷

Abstract: Effect of combustion modes (including compression ignition direct injection (CIDI), homogeneous charge compression ignition (HCCI) and compound charge compression ignition (CCCI) combustion) on NSDs of exhaust particles from engines fuelled with n-heptane was studied. The results indicate that the structure of NSDs for n-heptane changes with premixed ratio（rp） obviously. The accumulation mode dominates in CIDI case. With the increase of rp, the accumulation mode decreases, the nucleation mode increases significantly. In HCCI case, the nucleation mode occupies the dominant part of the total particles, and the number concentration of accumulation mode is very low. And the total exhaust particles number concentrations for CCCI and HCCI are obviously higher than those of CIDI. In addition, the number concentration of nucleation mode is highly correlation with HC concentrations.

Key words: combustion mode, exhaust, ultrafine particle, n-heptane

中图分类号:

TK16

刘炜1, 2, 黄震1. 不同燃烧模式下正庚烷燃烧发动机排气超细颗粒特性[J]. 上海交通大学学报（自然版）, 2011, 45(06): 837-841.

LIU Wei-1, 2 , HUANG Zhen-1. Effects of Combustion Modes on Exhaust Particle Size Distributions from a Diesel Engine Fueled with n-Heptane[J]. Journal of Shanghai Jiaotong University, 2011, 45(06): 837-841.

参考文献

［1］Zhang J J, Qiao X Q, Guan B, et al. Search for the optimizing control method of compound charge compression ignition (CCCI) combustion in an engine fueled with dimethyl ether［J］. Energy & Fuels, 2008, 22(3): 15811588.

［2］Wu J H, Huang Z, Qiao X Q, et al. Study on combustion and emissions characteristics of turbocharged engine fuelled with dimethyl ether［J］. International Journal of Automotive Technology, KSAE, 2006, 7(6): 645652.

［3］尧命发，许斯都. 直喷式柴油机燃用二甲基醚（DME）试验研究［J］. 燃烧科学与技术，2002,8(3):252257.

YAO Mingfa, XU Sidu. Experimental investigation on burning dimethyl ether (DME) in direct injection diesel engine［J］. Journal of Combustion Science and Technology, 2002,8(3): 252257.

［4］Liu W, Huang Z, Wang J S, et al. Effects of dimethoxy methane blended with GTL on particulate matter emissions from a compressionignition engine［J］. Energy & Fuels, 2008, 22(4): 23072313.

［5］Lee D, Miller A, Kittelson D. Characterization of metalbearing diesel nanoparticles using singleparticle mass spectrometry［J］. Aerosol Science, 2006, 37(1): 88110.

［6］刘炜，张武高，李新令,等. 低硫柴油直喷燃烧超细颗粒排放特性研究［J］.科学通报, 2009, 54(12): 17731778.

LIU Wei, ZHANG Wugao, LI Xinling, et al. Characteristics of ultrafine particle from a compressionignition engine fueled with low sulfur diesel［J］. Chinese Science Bulletin, 2009, 54(12): 17731778.

［7］Desantes J M, Bermúdez V, García J M, et al. Effects of current engine strategies on the exhaust aerosol particle size distribution from a heavyduty diesel engine［J］. Aerosol Science, 2005, 36(10):12511276.

［8］Liu W, Qiao X Q, Wang J S, et al. Effects of combustion mode on exhaust particle size distribution produced by an engine fueled by Dimethyl Ether (DME)［J］. Energy & Fuels, 2008, 22 (6): 38383843.

［9］马骏骏. 基于燃料设计与管理的HCCI/DI分层复合燃烧的试验研究［D］.上海：上海交通大学机动学院,2009.

［10］李新令. 发动机超细颗粒排放特性及排气稀释过程中其形成和变化研究［D］.上海：上海交通大学环境学院，2007.

［11］Vaaraslahti K, Virtanen A, Ristimki J, et al. Nucleation mode formation in heavyduty diesel exhuast with and without a particulate filter［J］. Environmental Science and Technology, 2004, 38(18):48844890.

[1]	王聚团, 戚晓宁, 黄志明. 水下生产管汇测试技术及其改进研究[J]. 海洋工程装备与技术, 2022, 9(2): 43-49.
[2]	袁振钦, 邹科, 孙亚峰, 刘刚, 屈衍, 李居跃. 基于时域分析法的动态电缆疲劳分析[J]. 海洋工程装备与技术, 2022, 9(2): 50-55.
[3]	王娟, 杨明旺, 郑茂尧, 刘凌云, 赵立君. 高强钢在大型半潜式平台组块建造中的应用[J]. 海洋工程装备与技术, 2022, 9(1): 27-31.
[4]	陈欣, 赵晓磊, 王立坤, 肖德明, 张腾月. 深水大型吸力锚建造技术研究[J]. 海洋工程装备与技术, 2022, 9(1): 32-36.
[5]	尹彦坤, 易涤非. 半潜式生产平台船体结构关键节点工程临界评估[J]. 海洋工程装备与技术, 2022, 9(1): 52-57.
[6]	ZHANG Shengfa (张胜发), TANG Na (唐纳), SHEN Guofeng (沈国峰), WANG Han (王悍), QIAO Shan (乔杉). Universal Software Architecture of Magnetic Resonance-Guided Focused Ultrasound Surgery System and Experimental Study[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(4): 471-481.
[7]	MA Qunsheng (马群圣), CEN Xingxing (岑星星), YUAN Junyi (袁骏毅), HOU Xumin (侯旭敏). Word Embedding Bootstrapped Deep Active Learning Method to Information Extraction on Chinese Electronic Medical Record[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(4): 494-502.
[8]	安庆升, 孙立东, 武秋生. 碳纤维增强复合材料发射筒设计研究[J]. 空天防御, 2021, 4(2): 13-.
[9]	KONG Xiangqiang (孔祥强), MENG Xiangxi (孟祥熙), LI Jianbo (李见波), SHANG Yanping (尚燕平), CUI Fulin (崔福林) . Comparative Study on Two-Stage Absorption Refrigeration Systems with Different Working Pairs[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(2): 155-162.
[10]	ZHUANG Weimin (庄蔚敏), WANG Pengyue (王鹏跃), AO Wenhong (熬文宏), CHEN Gang (陈刚) . Experiment and Simulation of Impact Response of Woven CFRP Laminates with Different Stacking Angles[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(2): 218-230.
[11]	ZHOU Xuhui (周旭辉), ZHANG Wenguang (张文光), XIE Jie (谢颉). Effects of Micro-Milling and Laser Engraving on Processing Quality and Implantation Mechanics of PEG-Dexamethasone Coated Neural Probe[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(1): 1-9.
[12]	HUANG Ningning (黄宁宁), MA Yixin (马艺馨), ZHANG Mingzhu (张明珠), GE Hao (葛浩), WU Huawei (吴华伟). Finite Element Modeling of Human Thorax Based on MRI Images for EIT Image Reconstruction[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(1): 33-39.
[13]	WANG Xianjin, GAO Xu, YU Kuigang . Fixture Locating Modelling and Optimization Research of Aluminum Alloy Sidewall in a High-Speed Train Body[J]. J Shanghai Jiaotong Univ Sci, 2020, 25(6): 706-713.
[14]	QIAO Xing, MA Dan, YAO Xuliang, FENG Baolin. Stability and Numerical Analysis of a Standby System[J]. J Shanghai Jiaotong Univ Sci, 2020, 25(6): 769-778.
[15]	WU Jin, MIN Yu, YANG Xiaodie, MA Simin . Micro-Expression Recognition Algorithm Based on Information Entropy Feature[J]. Journal of Shanghai Jiao Tong University(Science), 2020, 25(5): 589-599.