汽车轮辐错距强力旋压成形的有限元仿真

摘要/Abstract

摘要：

摘要：利用ABAQUS软件建立轮辐三旋轮的错距强力旋压过程的弹塑性有限元仿真模型，并对成形过程进行分析；给出了仿真模型边界条件的施加方法和旋轮旋压轨迹曲线的加载方法；通过计算动能及伪应变能与内能的比率，并采用逆向扫描技术和实验测量方法对比分析仿真结果与轮辐生产件，以验证所建立模型的正确性.结果表明：与尾顶接触的材料不发生塑性变形，其他部位材料沿轮辐周向的塑性变形程度相当，而沿母线方向的塑性变形程度不同，并形成了等效塑性应变环和厚度环；在成形轮辐弯曲圆角处和外缘收口区域，材料的塑性变形程度较大，且材料堆积缺陷易出现在成形轮辐外缘收口区域；沿母线方向上不同位置处的轮辐的壁厚不同，壁厚变化遵循正弦规律.

关键词: , 汽车轮辐, 错距旋压, 成形, 有限元仿真

Abstract:

Abstract： In order to make an indepth research on stagger spinning process of automobile spoke with three rollers, the elasticplastic finite element simulation model was established and the forming process was analyzed based on ABAQUS. The methods for imposing boundary conditions and trajectory curves of rollers were introduced. The correctness of the simulation model was verified by calculating the ratios of kinetic energy and pseudo strain energy to internal energy and by comparing simulation results with production parts by using the reverse technique and experimental measurement. The results show that the material does not produce plastic deformation in the central area of the blank contacting with tailstock. Plastic deformation distributes homogeneously in the circumferential direction of the spoke and changes in the radial direction. Thus equivalent plastic strain rings and thickness rings are formed. Plastic deformation is severe when forming curved fillet areas and outer edge regions of the spoke. Material accumulation defect is likely to occur when forming outer edge regions of the spoke. The thickness of the spoke is different along the generatrix direction, and it changes in accordance with the sine law.

Key words: automobile spoke, stagger spinning, forming, finite element method (FEM) simulation

中图分类号:

TG 306

路平1a,1b，张云开1a,1b，陈波2. 汽车轮辐错距强力旋压成形的有限元仿真[J]. 上海交通大学学报（自然版）, 2015, 49(01): 56-61.

LU Ping1a,1b,ZHANG Yunkai1a,1b,CHEN Bo2. Finite Element Method Simulation of Stagger Power Spinning Forming of Automobile Spoke[J]. Journal of Shanghai Jiaotong University, 2015, 49(01): 56-61.

参考文献

［1］张治民, 王强, 路光, 等. 重型车辆铝合金轮辋挤压成形技术及应用［J］. 机械工程学报, 2012, 48(18): 5559.

ZHANG Zhimin, WANG Qiang, LU Guang, et al. Research on extrusion technology and application for aluminum alloy wheel rim of heavy vehicles ［J］. Journal of Mechanical Engineering, 2012, 48(18): 5559.

［2］王慧玲. 轮辋滚压过程仿真与成形工艺研究［D］. 上海交通大学机械与动力工程学院, 2009.

［3］杨合, 詹梅, 李甜, 等. 铝合金大型复杂薄壁壳体旋压研究进展［J］. 中国有色金属学报, 2011, 21(10): 25342550.

YANG He, ZHAN Mei, LI Tian, et al. Advances in spinning of aluminum alloy largesized complicated thinwalled shells ［J］. Chinese Journal of Nonferrous Metals, 2011, 21(10): 25342550.

［4］Music O, Allwood J M, Kawai K. A review of the mechanics of metal spinning ［J］. Journal of Materials Processing Technology, 2010, 210(1): 323.

［5］王彦菊, 方刚, 张剑寒, 等. 变厚度轮辐强力旋压成形过程的分析［J］. 材料科学与工艺, 2012, 20(3): 103108.

WANG Yanju, FANG Gang, ZHANG Jianhan, et al. Finite element simulation for the spinning process of an automobile spokes with varying thickness ［J］. Materials Science and Technology, 2012, 20(3): 103108.

［6］Bai Q, Yang H, Zhan M. Finite element modeling of power spinning of thinwalled shell with hoop inner rib ［J］. Transactions of Nonferrous Metals Society of China, 2008, 18(1): 613.

［7］Sebastiani G, Brosius A, Ewers R, et al. Numerical investigation on dynamic effects during sheet metal spinning by explicit finiteelementanalysis ［J］. Journal of Materials Processing Technology, 2006, 177(13): 401403.

［8］Mohebbi M S, Akbarzadeh A. Experimental study and FEM analysis of redundant strains in flow forming of tubes ［J］. Journal of Materials Processing Technology, 2010, 210(2): 38939.

［9］曾国, 来新民, 于忠奇, 等. 多道次辊弯成形数值模拟技术［J］.上海交通大学学报, 2007, 41(10): 15981602.

ZENG Guo, LAI Xinmin,YU Zhongqi, et al. The Simulation of roll forming with multiple passes［J］. Journal of Shanghai Jiaotong University, 2007, 41(10): 15981602.

［10］李玉强, 崔振山, 阮雪榆, 等. 工艺参数对多道次拉旋应力应变分布的影响规律［J］. 塑性工程学报, 2004, 11(5): 1722.

LI Yuqiang, CUI Zhenshan, RUAN Xueyu, et al. Effects of parameters on the distributions of stress and strain of multiprocess drawspinning ［J］. Journal of Plasticity Engineering, 2004, 11(5): 1722.

［11］马飞, 杨合, 詹梅. 工艺参数对平板毛坯普旋成形的影响规律［J］. 机械科学与技术, 2007, 26(3): 309313.

MA Fei, YANG He, ZHAN Mei. Influence of process parameters on conventional spinning formation process ［J］. Mechanical Science and Technology, 2007, 26(3): 309313.

［12］Wang L, Long H. Investigation of material deformation in multipass conventional metal spinning ［J］. Materials and Design, 2011, 32(5): 28912899.

［13］Chen M D, Hsu R Q, Fuh K H. Forecast of shear spinning force and surface roughness of spun cones by employing regression analysis ［J］. International Journal of Machine Tools and Manufacture, 2001, 41(12): 17211734.

［14］Sekiguchi A, Arai H. Control of wall thickness distribution by oblique shear spinning methods ［J］. Journal of Materials Processing Technology, 2012, 212(4): 786793.

［15］詹梅, 李虎, 杨合, 等. 大型复杂薄壁壳体多道次旋压过程中的壁厚变化［J］. 塑性工程学报, 2008, 15(2): 115121.

ZHAN Mei, LI Hu, YANG He, et al. Wall thickness variation during multipass spinning of large complicated shell ［J］. Journal of Plasticity Engineering, 2008, 15(2): 115121.

［16］Zoghi H, Arezoodar A F, Sayeaftabi M. Enhanced finite element analysis of material deformation and strain distribution in spinning of 42CrMo steel tubes at elevated temperature ［J］. Materials and Design, 2013, 47：234242.

[1]	马遵农, 张延松, 赵亦希. 多层箔片超声焊接的摩擦能量耗散机理及影响因素研究[J]. 上海交通大学学报, 2022, 56(6): 772-783.
[2]	唐耿林, 李建军, 李元辉, 张珑耀, 朱文峰. 基于胶层填充的薄板包边成形数值模拟及实验研究[J]. 上海交通大学学报, 2022, 56(4): 523-531.
[3]	王聚团, 戚晓宁, 黄志明. 水下生产管汇测试技术及其改进研究[J]. 海洋工程装备与技术, 2022, 9(2): 43-49.
[4]	袁振钦, 邹科, 孙亚峰, 刘刚, 屈衍, 李居跃. 基于时域分析法的动态电缆疲劳分析[J]. 海洋工程装备与技术, 2022, 9(2): 50-55.
[5]	郑高媛, 赵亦希, 崔峻辉. 车身用铝饰条拉弯成形面畸变缺陷形成规律[J]. 上海交通大学学报, 2022, 56(1): 53-61.
[6]	周宇, 赵勇, 于忠奇, 赵亦希. 交叉内筋薄壁筒体错距旋压成形数值仿真[J]. 上海交通大学学报, 2022, 56(1): 62-69.
[7]	王娟, 杨明旺, 郑茂尧, 刘凌云, 赵立君. 高强钢在大型半潜式平台组块建造中的应用[J]. 海洋工程装备与技术, 2022, 9(1): 27-31.
[8]	陈欣, 赵晓磊, 王立坤, 肖德明, 张腾月. 深水大型吸力锚建造技术研究[J]. 海洋工程装备与技术, 2022, 9(1): 32-36.
[9]	尹彦坤, 易涤非. 半潜式生产平台船体结构关键节点工程临界评估[J]. 海洋工程装备与技术, 2022, 9(1): 52-57.
[10]	MA Qunsheng (马群圣), CEN Xingxing (岑星星), YUAN Junyi (袁骏毅), HOU Xumin (侯旭敏). Word Embedding Bootstrapped Deep Active Learning Method to Information Extraction on Chinese Electronic Medical Record[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(4): 494-502.
[11]	李晓凯, 赵亦希, 于忠奇, 朱宝行, 崔峻辉. 铝合金带筋构件超声辅助旋压仿真研究[J]. 上海交通大学学报, 2021, 55(4): 394-402.
[12]	ZHANG Shengfa (张胜发), TANG Na (唐纳), SHEN Guofeng (沈国峰), WANG Han (王悍), QIAO Shan (乔杉). Universal Software Architecture of Magnetic Resonance-Guided Focused Ultrasound Surgery System and Experimental Study[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(4): 471-481.
[13]	安庆升, 孙立东, 武秋生. 碳纤维增强复合材料发射筒设计研究[J]. 空天防御, 2021, 4(2): 13-.
[14]	KONG Xiangqiang (孔祥强), MENG Xiangxi (孟祥熙), LI Jianbo (李见波), SHANG Yanping (尚燕平), CUI Fulin (崔福林) . Comparative Study on Two-Stage Absorption Refrigeration Systems with Different Working Pairs[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(2): 155-162.
[15]	ZHUANG Weimin (庄蔚敏), WANG Pengyue (王鹏跃), AO Wenhong (熬文宏), CHEN Gang (陈刚) . Experiment and Simulation of Impact Response of Woven CFRP Laminates with Different Stacking Angles[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(2): 218-230.