The ultra-high-strength steel (UHSS) plays an important role in the mechanical industry because of
their special performances. The machinability of 30CrMnSiNi2A steel was studied in dry milling with two different
coated tools in the present work. This paper introduced that 30CrMnSiNi2A steel was a kind of difficult-to-machine
materials. The results showed that the cutting force components of feed direction and cutting width direction,
i.e. Fx and Fy, increased slightly with increasing the cutting speed and feed rate. The values of axial force
component Fz were much larger than Fx and Fy, and increased obviously with increasing the milling speed. The
workpiece surface had the minimum roughness at the cutting speed of 150 m/min. The physical vapor deposition
(PVD) coated ((Ti, Al)N-TiN) insert was more suitable for machining 30CrMnSiNi2A steel than the chemical
vapor deposition (CVD) coated (Ti(C, N)-Al2O3) insert. Moreover, the main failure modes of PVD-coated insert
were micro-chipping and coating spalling. The wear modes of CVD-coated insert were ploughing, coating spalling,
and cratering. The serious adhesive wear and the abrasion with some adhesion were the main wear mechanism of
PVD- and CVD-coated inserts, respectively.
NIU Qiu-lin1 (牛秋林), DONG Da-peng1 (董大鹏), CHEN Ming1* (陈 明), ZHANG Yu-sheng2 (张余升), WANG Cheng-dong1 (王呈栋)
. Dry Milling of the Ultra-High-Strength Steel 30CrMnSiNi2A with Coated Carbide Inserts[J]. Journal of Shanghai Jiaotong University(Science), 2013
, 18(4)
: 468
-473
.
DOI: 10.1007/s12204-013-1410-5
[1] Ford. Ultra-high-strength steels [EB/OL]. (2012-04-30). http://media.ford.com.
[2] Long Z H, Wang X B, Liu Z B. Machinability of an ultra high strength alloy steel in milling processing [J].Key Engineering Materials, 2004, 259-260: 435-440.
[3] An Q L, Fu Y C, Xu J H. Experimental study on turning of TC9 titanium alloy with cold water mist jet cooling [J]. International Journal of Machine Tools and Manufacture, 2011, 51: 549-555.
[4] Manoj Kumar B V, Ram Kumar J, Basu B. Crater wear mechanisms of TiCN-Ni-WC cermets during dry machining [J]. International Journal of Refractory Metals and Hard Materials, 2007, 25: 392-399.
[5] Deng J X, Wu Z, Lian Y S, et al. Performance of carbide tools with textured rake-face filled with solid lubricants in dry cutting processes [J]. International Journal of Refractory Metals and Hard Materials, 2012, 30: 164-172.
[6] Nouari M, Ginting A. Wear characteristics and performance of multi-layer CVD-coated alloyed carbide tool in dry end milling of titanium alloy [J]. Surface and Coatings Technology, 2006, 200: 5663-5676.
[7] Liu A H, Deng J X, Cui H B, et al. Friction and wear properties of TiN, TiAlN, AlTiN and CrAlN PVD nitride coatings [J]. International Journal of Refractory Metals and Hard Materials, 2012, 31: 82-88.
[8] Jindal P C, Santhanam A T, Schleinkofer U, et al. Performance of PVD TiN, TiCN, and TiAlN coated cemented carbide tools in turning [J]. International Journal of Refractory Metals and Hard Materials, 1999, 17: 163-170.
[9] Gaitonde V N, Karnik S R, Luis F, et al. Machinability investigations in hard turning of AISI D2 cold work tool steel with conventional and wiper ceramic inserts [J]. International Journal of Refractory Metals and Hard Materials, 2009, 27: 754-763.
[10] Khrais S K, Lin Y J. Wear mechanisms and tool performance of TiAlN PVD coated inserts during machining of AISI 4140 steel [J]. Wear, 2007, 262: 64-69.
[11] Chakraborty P, Asfour S, Cho S, et al. Modeling tool wear progression by using mixed effects modeling technique when end-milling AISI 4340 steel [J]. Journal of Materials Processing Technology, 2008, 205: 190-202.
[12] Wu H J, Yao W, Huang F L, et al. Experimental investigation on spall fracture of 30CrMnSiNi2A steel [J]. Journal of Beijing Institute of Technology, 2010, 19(1): 1-7.
[13] Antonialli A ′I S, Diniz A E, Pederiva R. Vibration analysis of cutting force in titanium alloy milling [J]. International Journal of Machine Tools and Manufacture, 2010, 50: 65-74.
[14] Cheng Ri-yao. Principle of metal cutting [M]. Beijing: China Machine Press, 2002 (in Chinese).
[15] Sahin Y, Motorcu A R. Surface roughness model in machining hardened steel with cubic boron nitride cutting tool [J]. International Journal of Refractory Metals and Hard Materials, 2008, 26: 84-90.
[16] Bonifacio M E R, Dinz A E. Correlating tool wear, tool life, surface roughness and tool vibration in finish turning with coated carbide tools [J]. Wear, 1994, 173: 137-144.
[17] More A S, Jiang W P, Brown W D, et al. Tool wear and machining performance of cBN-TiN coated carbide inserts and PCBN compact inserts in turning AISI 4340 hardened steel [J]. Journal of Materials Processing Technology, 2006, 180: 253-262.
