Front wall beams and the support of A-Pillar are usually hot-stamped parts in side impact of vehicle, and front panel is made of mild steel with excellent formability by stamping, hence the area has formed a typical three-sheet resistance spot welded joints of unequal thickness and strength. In order to improve the overall load bearing capacity of spot welding joints, the paper investigates the influence of different lapping orders on overall mechanical properties of welded joints. Based on three kinds of material with unequal thickness and strength， B1500HS-1.4mm, B1500HS-1.6mm and DC06-0.8mm, the mechanical properties of different interfaces of two welded joints (strong-strong-soft and strong-soft-strong) under different lapping orders were compared. The nugget forming process, microstructure of nugget, fusion zone size and microhardness were also studied and analyzed. By investigating microstructure formation of nugget process of welded joints under different lapping orders, this paper reveals that the joint of strong-soft-strong can increase the bearing capacity. Finally, the article gives a reasonable design of strong-soft-strong lap joint in side impact of A-pillar and improves overall crashworthiness of vehicle.
ZHU Qiang,QIN Fei,WANG Wurong,WEI Xicheng
. Mechanical Properties of Three-Sheet Resistance Spot Welded Joints
Under Different Lapping Orders[J]. Journal of Shanghai Jiaotong University, 2019
, 53(9)
: 1122
-1129
.
DOI: 10.16183/j.cnki.jsjtu.2019.09.015
［1］杜汉斌, 朱强, 王武荣, 等. 三层板电阻点焊接头界面力学性能［J］. 精密成形工程, 2017, 9(5): 192-197.
DU Hanbin, ZHU Qiang, WANG Wurong, et al. Mechanical properties of three-layer resistance spot welding joint interface［J］. Journal of Netshape Forming Engineering, 2017, 9(5): 192-197.
［2］李效文, 盈亮, 申国哲, 等. 高强度热成形钢点焊性能与接头组织［J］. 电焊机, 2012, 42(12): 92-96.
LI Xiaowen, YING Liang, SHEN Guozhe, et al. Research on the spot welding performance and the joint microstructure of the hot forming high strength steel［J］. Electric Welding Machine, 2012, 42(12): 92-96.
［3］张文瑞. 汽车用超深冲钢DC06拉深数值模拟及成形性能研究［D］. 上海: 上海工程技术大学, 2015.
ZHANG Wenrui. Super deep drawing automotive steel DC06 deep drawing forming numerical simulation and performance study［D］. Shanghai: Shanghai University of Engineering Science, 2015.
［4］OZSARAC U. Investigation of mechanical properties of galvanized automotive sheets joined by resistance spot welding［J］. Journal of Materials Engineering and Performance, 2012, 21: 748-755.
［5］CHOI H S, PARK G H, LIM W S, et al. Evaluation of weldability for resistance spot welded single-lap joint between GA780DP and hot-stamped 22MnB5 steel sheets［J］. Journal of Mechanical Science and Technology, 2011, 25(6): 1543-1550.
［6］LIU C J, ZHENG X K, WANG W R, et al. Effect of work hardening on mechanical behavior of resistance spot welding joint during tension shear test［J］. Materials and Design, 2016, 100: 188-197.
［7］杨柳, 程轩挺, 孙游, 等. 超高强热成形钢B1500HS的电阻点焊工艺和接头性能［J］. 上海交通大学学报, 2012, 46(7): 1103-1106.
YANG Liu, CHENG Xuanting, SUN You, et al. Technology and weldability of resistance spot welding of B1500HS hot-stamped steel［J］. Journal of Shanghai Jiao Tong University, 2012, 46(7): 1103-1106.
［8］唐虹, 李军锋, 宋清, 等. 含镀锌板的三层板点焊熔核形成机理研究［J］. 热加工工艺, 2013, 42(1): 142-144.
TANG Hong, LI Junfeng, SONG Qing, et al. Nugget formation mechanism of resistance spot welding of three-sheet including galvanized sheet［J］. Hot Working Technology, 2013, 42 (1): 142-144.
［9］颜福裕, 李洋, 罗震, 等. 三层板6061铝合金点焊接头形式对其力学性能的影响［J］. 焊接学报, 2016, 37(4): 81-84.
YAN Fuyu, LI Yang, LUO Zhen, et al. Effect of joint type on mechanical properties of three-sheet 6061 aluminum alloy resistance spot welds［J］. Tran-sactions of the China Welding Institution, 2016, 37(4): 81-84.
［10］TAVASOLIZADEH A, MARASHI S P H, POURANVARI M. Mechanical performance of three thickness resistance spot welded low carbon steel［J］. Materials Science and Technology, 2011, 27(1): 219-224.
［11］POURANVARI M, MARASHI S P H. Weld nugget formation and mechanical properties of three-sheet resistance spot welded low carbon steel［J］. Canadian Metallurgical Quarterly, 2012, 51(1): 105-110.
