Welding is the most widely used connection mode in the assembly process of the electric multiple unit (EMU) while the deformation induced by welding will have a great influence on the assembly precision. The influence of welding deformation on the assembly precision of the sidewall window module is discussed in this paper. Firstly, the inherent strain of three typical welded joints in the sidewall window module of the EMU is extracted by the thermal elastic-plastic finite element method. Then, the deformation of the sidewall window module is obtained by the finite element simulation based on the inherent strain method. The obtained deformation is considered as a mean shift to amend the 3D assembly variation simulation results of the window module. Finally, the amended simulation results are compared with the measured data. The simulation results of assembly variation considering welding deformation have a good agreement with the actual measured data which indicates that the proposed method is more accurate and feasible for predicting the assembly variation of the sidewall window module of the EMU.
YAO Limin，ZHANG Daoliu，HOU Xiujuan，LIU Tao，LI Zhimin
. Assembly Deviation Simulation Considering Welding Deformation
Applied on Electric Multiple Unit[J]. Journal of Shanghai Jiaotong University, 2019
, 53(3)
: 260
-268
.
DOI: 10.16183/j.cnki.jsjtu.2019.03.002
［1］吴桃生, 李志敏, 王华, 等. 基于工装预变形的高速列车侧墙尺寸偏差控制方法［J］. 铁道机车车辆, 2012, 32(1): 1-5.
WU Taosheng, LI Zhimin, WANG Hua, et al. Variation control method for the sidewall of highspeed train based on fixture’s pre-variation［J］. Railway Locomotive & Car, 2012, 32(1): 1-5.
［2］张风东, 刘胜龙. 高速动车组铝合金车体底架焊接变形控制［J］. 机车车辆工艺, 2012, (6): 22-23.
ZHANG Fengdong, LIU Shenglong. Control measure of deformation on auto welding technology of underframe on EMU ［J］. Locomotive & Rolling Stock Technology, 2012, (6): 22-23.
［3］DENG D, MURAKAWA H. Numerical simulation of temperature field and residual stress in multi-pass welds in stainless steel pipe and comparison with experimental measurements ［J］. Computational Materials Science, 2006, 37(3): 269-277.
［4］TENG T L, FUNG C P, CHANG P H, et al. Analysis of residual stresses and distortions in T-joint fillet welds ［J］. International Journal of Pressure Vessels & Piping, 2001, 78(8): 523-538.
［5］PERI M, TONKOVI Z, RODI A, et al. Numerical analysis and experimental investigation of welding residual stresses and distortions in a T-joint fillet weld ［J］. Materials and Design, 2014, 53: 1052-1063.
［6］UEDA Y, YUAN M G. Prediction of residual stresses in butt welded plates using inherent strains ［J］. Journal of Engineering Materials & Technology, 1993, 115(4): 417-423.
［7］DENG D, MURAKAWA H. FEM prediction of buckling distortion induced by welding in thin plate panel structures ［J］. Computational Materials Science, 2008, 43(4): 591-607.
［8］DENG D, MURAKAWA H, LIANG W. Numerical simulation of welding distortion in large structures ［J］. Computer Methods in Applied Mechanics & Engineering, 2007, 196(45/48): 4613-4627.
［9］LEE J M, SEO H D, CHUNG H. Efficient welding distortion analysis method for large welded structures ［J］. Journal of Materials Processing Technology, 2018, 256: 36-50.
［10］LEE D, KWON K E, LEE J, et al. Tolerance analysis considering weld distortion by use of pregenerated database ［J］. Journal of Manufacturing Science and Engineering, 2009, 131(4): 041012.
［11］PAHKAMAA A, WRMEFJORD K, KARLSSON L, et al. Combining variation simulation with welding simulation for prediction of deformation and variation of a final assembly ［J］. Journal of Computing and Information Science in Engineering, 2012, 12(2): 021002-021007.
［12］LORIN S, CROMVIK C, EDELVIK F, et al. Variation simulation of welded assemblies using a thermo-elastic finite element model ［J］. Journal of Computing and Information Science in Engineering, 2014, 14(3): 031003.
［13］LORIN S, CROMVIK C, EDELVIK F, et al. Simulation of non-nominal welds by resolving the melted zone and its implication to variation simulation［C］//ASME 2014 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference. New York, USA: ASME, 2014: V004T06A018.
［14］WRMEFJORD K, SDERBERG R, ERICSSON M, et al. Welding of non-nominal geometries-physical tests ［J］. Procedia CIRP, 2016, 43: 136-141.
［15］RENZI C, PANARI D, LEALI F. Predicting tolerance on the welding distortion in a thin aluminum welded T-joint ［J］. The International Journal of Advanced Manufacturing Technology, 2018, 96(5/8): 2479-2494.
［16］汪建华, 陆皓, 魏良武. 固有应变有限元法预测焊接变形理论及其应用［J］. 焊接学报, 2002, 23(6): 36-40.
WANG Jianhua, LU Hao, WEI Liangwu. Prediction of welding distortions based on theory of inherent strain by FEM and its application ［J］. Transactions of the China Welding Institution, 2002, 23(6): 36-40.
［17］李红涛, 宋绪丁. 不同热源模型对Q345中厚板焊接温度场的影响［J］. 热加工工艺, 2017, 46(23): 205-209.
LI Hongtao, SONG Xuding. Influence of different heat source models on welding temperature field of Q345 medium plate ［J］. Hot Working Technology, 2017, 46(23): 205-209.
