In order to investigate effects of assembly temperature on thermal reological lubricating performance with load impact in ball bearings, by using the Eyring shear-thinning fluid, a thermal reological elastohydrodynamic lubrication (EHL) model with a load impact in ball bearings was established. The model considered differences of the temperature between the assembly and the supplied oil. Multi-grid method and the numerical technique for time-dependent, reology and temperature field were used. Effects of the assembly temperature on the thermal reological lubricating performance of the dynamic oil film were investigated, and phenomena of thermal failure at extreme cases were analyzed as well. Results show that, differring from the convertional solution, the assembly temperature has much more influence on thermal EHL performance of the dynamic oil film. The higher the temperature of the ball, the less the film thickness and the frictional coefficient. At extreme cases, phenomena of high pressure, high temperature, and thin film appear for a bearing inner race-rolling element contact. Moreover, the temperature of the bearing inner race is up to the first critical temperature of desorption for the boundary film. In addition, the bearing inner race-ball contact is in a state of mixed lubrication. Therefore, effects of the temperature field in ball bearings should be considered in analysis of non-steady state thermal reological EHL.
LIU Xiaoling,YANG Yubing,YANG Peiran
. Effects of Assembly Temperature on Thermal Reological Lubricating
Performance with Load Impact in Ball Bearings[J]. Journal of Shanghai Jiaotong University, 2018
, 52(5)
: 545
-553
.
DOI: 10.16183/j.cnki.jsjtu.2018.05.007
［1］SPIKES H, ZHANG J. History, origins and prediction of elastohydrodynamic friction［J］. Tribology Letters, 2014, 56(1): 1-25.
［2］卢宪玖, 王优强, 刘昺丽, 等.球轴承启停过程的瞬态热混合润滑分析［J］. 摩擦学学报, 2015, 35(1): 75-81.
LU Xianjiu, WANG Youqiang, LIU Bingli, et al. Transient thermal mixed lubrication analysis in the process of start-up and shut-down of ball bearing［J］. Tribology, 2015, 35(1): 75-81.
［3］FRYZA J, SPERKA P, KANETA M, et al. Effects of lubricant rheology and impact speed on EHL film thickness at pure squeeze action［J］. Tribology International, 2017, 106: 1-9.
［4］LIU X L, YANG P R. On the thermal elastohydrodynamic lubrication of tilting roller pairs［J］. Tribology International, 2013, 65(3): 346-353.
［5］艾思源. 滚动轴承温度分布及润滑性能研究［D］. 北京: 北京理工大学机械与车辆学院, 2015.
AI Siyuan. Study on the temperature distribution and lubrication performance of rolling bearing ［D］. Beijing: School of Mechanical Engineering, Beijing Institute of Technology, 2015.
［6］LIU X L, YANG P R. Influence of solid body temperature on the thermal EHL behavior in circular contact［J］. ASME Journal of Tribology, 2008, 130(1): 125-128.
［7］哈姆罗克 B J, 道森 D. 滚动轴承润滑 ［M］. 汪一麟译.北京: 机械工业出版社, 1988.
HAMROCK B J, DOWSON D. Rolling bearing lubrication［M］. WANG Yilin trans. Beijing: China Machine Press, 1988.
［8］LIU X L, JIANG M, YANG P R, et al. Non-newtonian thermal analyses of point EHL contacts using the Eyring model［J］. ASME Journal of Tribology, 2005, 127(1): 70-81.
［9］杨沛然. 流体润滑数值分析 ［M］. 北京: 国防工业出版社, 1998.
YANG Peiran. Numerical analysis of fluid lubrication［M］. Beijing: National Defense Industry Press, 1998.
［10］孙浩洋, 杨沛然, 陈晓阳. 滚滑工况弹流反常温度场的研究［J］. 摩擦学学报, 2004, 24(1): 66-69.
SUN Haoyang, YANG Peiran, CHEN Xiaoyang. Study on abnormal temperature field of slide/roll contact under elastohydrodynamic lubrication［J］. Tribology, 2004, 24(1): 66-69.
［11］哈里斯 T A, 科兹拉斯 M N. 滚动轴承分析 ［M］. 罗继伟等译.北京: 机械工业出版社, 2010.
HARRIS T A, KOTZALAS M N. Rolling bearing analysis［M］. LUO Jiwei, et al. trans. Beijing: China Machine Press, 2010.
［12］杨玉冰. 考虑轴承组件温度边界的动态油膜热弹流润滑分析［D］. 青岛: 青岛理工大学机械工程学院, 2017.
YANG Yubing. Analysis of dynamic oil film thermal EHL considering boundary temperature of bearing components［D］. Qingdao: School of Mechanical Engineering, Qingdao University of Technology, 2017.
［13］温诗铸,黄平. 摩擦学原理 ［M］. 2版.北京: 清华大学出版社, 2002.
WEN Shizhu, HUANG Ping. Principles of tribology［M］. 2nd ed. Beijing: Tsinghua University Press, 2002.
