Mathematical Model and Performance Analysis with Variable Condition of Enthalpy Recovery Wheel

Abstract

Abstract:

The mathematical model of enthalpy recovery wheel was built and verified by comparison with existing literatures, based on which, the effects of air velocity, proportion of fresh air and exhaust air, fresh air temperature (when humidity ratio is constant or relative humidity is constant), fresh air humidity ratio on the heat recovery efficiency of enthalpy recovery wheel were investigated. The results show that the sensible heat efficiency, latent heat efficiency and total heat efficiency of enthalpy recovery wheel decrease with increasing of air velocity; when proportion of fresh air and exhaust air increases, or fresh air temperature increases (relative humidity is constant), and the sensible heat efficiency, latent heat efficiency and total heat efficiency increase, too; with increasing of fresh air temperature (humidity ratio is constant ), the sensible heat efficiency increases, while the latent heat efficiency and total heat efficiency decrease; when fresh air humidity ratio increases, the sensible heat efficiency remains constant, while the latent heat efficiency and total heat efficiency increase.

Key words: enthalpy recovery wheel, mathematical model, heat recovery efficiency, variable condition

CLC Number:

TU 831

FANG Jihua，GU Bo，ZHANG Jie. Mathematical Model and Performance Analysis with Variable Condition of Enthalpy Recovery Wheel[J]. Journal of Shanghai Jiaotong University, 2014, 48(06): 809-815.

References

［1］钱以明，董启平.转轮式全热交换器结构参数的优化［J］.制冷学报，1990(4)：612.

QIAN Yiming, DONG Qiping. The optimization of the structural dimensions for rotary total heat exchanger ［J］. Journal of Refrigeration, 1990(4):612.

［2］江亿.温湿度独立控制空调系统［M］.北京：中国建筑工业出版社，2006.

［3］Nóbrega C E L, Brum N C L. Modeling and simulation of heat and enthalpy recovery wheels ［J］. Energy, 2009, 34(12): 20632068.

［4］Wu Z, Melnik R V N, Borup F. Modelbased analysis and simulation of regenerative heat wheel ［J］. Energy and Buildings, 2006, 38(5):502514.

［5］Wei R, Ming Q, Horton W T. Modeling analysis of an enthalpy recovery wheel with purge air ［J］.

International Journal of Heat and Mass Transfer, 2012, 55(1718): 46654672.

［6］Sphaier L A, Worek W M. The effect of axial diffusion in desiccant and enthalpy wheels ［J］.

International Journal of Heat and Mass Transfer, 2006, 49(78): 14121419.

［7］腊栋，蔡世佳，代彦军，等.基于不同干燥剂的焓轮式全热回收器特性数值模拟［J］.化工学报，2008，59(S2)：6469.

LA Dong, CAI Shijia, DAI Yanjun, et al. Numerical simulation of characteristics of enthalpy recovery wheel with different desiccants ［J］. Journal of Chemical Industry and Engineering, 2008, 59(S2):6469.

［8］Jeong J W, Mumma S A. Practical thermal performance correlations for molecular sieve and silica gel loaded enthalpy wheels ［J］. Applied Thermal Engineering, 2005, 25(56):719740.

［9］Zhang L Z, Niu J L. Performance comparisons of desiccant wheels for air dehumidification and enthalpy recovery ［J］. Applied Thermal Engineering, 2002, 22(12):13471367.

［10］潘少华，祝刚.全热回收转轮的工作特性分析［J］.制冷空调与电力机械，2007，28(5)：7678.

PAN Shaohua, ZHU Gang. Character analysis on the running wheels of air ventilator with total thermal recovery ［J］. Refrigeration Air Conditioning & Electric Power Machinery, 2007, 28(5):7678.

［11］陆冬梅.转轮全热交换器对空调箱运行能耗的影响［J］.山西建筑，2010，36(9)：192193.

LU Dongmei. Rotate wheel heat exchanger’s influence on air conditioner’s operation energy consumption ［J］. Shanxi Architecture, 2010, 36(9):192193.

［12］张学军，代彦军，王如竹.蜂窝式除湿转轮的传热传质数学模型及其试验验证［J］.机械工程学报，2005，41(1)：8287.

ZHANG Xuejun, DAI Yanjun, WANG Ruzhu. Heat mass transfer model of a honeycombed desiccant wheel and experiment ［J］. Chinese Journal of Mechanical Engineering, 2005, 41(1):8287.

［13］PlaBarby F E, Vliet G C. Rotary bed solid desiccant drying: An analytical and experimental investigation［C］//ASME/AICHE 18th National Heat Transfer Conference. San Diego, USA:CA, 1979:78.

［14］陆耀庆.实用供热空调设计手册［M］.2版.北京：中国建筑工业出版社，2007.

［15］Simonson C J, Besant R W. Energy wheel effectiveness. Part II: Correlations ［J］. International Journal of Heat and Mass Transfer, 1999, 42(12):21712185.

[1]	WANG Zekun, ZHANG Fuxi. Modeling and Experimental Study of Tin Whiskers for 3D Electronic Packaging [J]. Journal of Shanghai Jiao Tong University, 2021, 55(11): 1445-1452.
[2]	WANG Wei, LI Aote, YU Junli. A Design Method for Flow Distribution in Micro-Combustor Based on Target Flow Fitting [J]. Journal of Shanghai Jiaotong University, 2020, 54(9): 1000-1006.
[3]	LI Meng (李蒙), ZHANG Yong* (张勇), LIU Fengyu (刘峰宇), YIN Chengliang (殷承良). Manual Transmission Gear Rattle Vibration Research Based on Mathematical and Multi-Body Dynamics Co-simulation and Experiment [J]. Journal of Shanghai Jiao Tong University (Science), 2019, 24(4): 524-533.
[4]	LIANG Xiaoyang,MA Ning,LIU Han,GU Xiechong. Test on Maneuverability in the Vertical Plane of a Revolution Submersible at Large Attack Angle in Circulating Water Channel [J]. Journal of Shanghai Jiaotong University, 2019, 53(12): 1395-1403.
[5]	HU Ming,WANG Jiong,FAN Yiqing. Mathematical Model of Orifice Outflow for Magnetorheological Fluid [J]. Journal of Shanghai Jiaotong University, 2017, 51(9): 1065-1070.
[6]	Li-jie WU, Juan YU, Jian-sheng SHI, Cheng-min WANG, Zhi-wei BI, Jiao GUO. Study on the Evolution Law of Potassium with Long Time Scale Climate Change in Jiangjun Loess Section of the Middle Reaches of the Jinghe River [J]. Journal of Shanghai Jiaotong University (Agricultural Sciences), 2016, 34(1): 69-73.
[7]	HUANG Jiahan,WANG xinjie,WANG Jiong. An Optically Driven Microgripper Based on Photostrictive Materials [J]. Journal of Shanghai Jiaotong University, 2014, 48(12): 1681-1687.
[8]	CHEN Xia,ZHANG Jing，XU Guangyan. Three-Dimension Path Planning for Unmanned Aerial Vehicle Under Moving Threat [J]. Journal of Shanghai Jiaotong University, 2014, 48(10): 1400-1405.
[9]	BAO Xi-rong1 (包喜荣), LIU Yu-yan1 (刘宇雁), LI Ge1 (李革), CHEN Lin1 (陈林) WANG Jian-guo1 (王建国), WU Zhang-zhong2 (吴章忠), TIAN Zhong-liang2 (田仲良). Research and Application of Pre-bending Automatic Control Models of 100 m Rail [J]. Journal of shanghai Jiaotong University (Science), 2012, 17(4): 465-469.
[10]	ZHAO Fu-Hai-a, b , HUA Xue-Ming-a, b , YE Xin-a, b , WU Yi-Xiong-a, b , c . Mathematical Model of Quasi-state Temperature Distribution of Hot-Wire during Hot-Wire TIG Welding Process [J]. Journal of Shanghai Jiaotong University, 2012, 46(07): 1063-1068.
[11]	JIA Wen-Hua- , YIN Chen-Bo. Modeling and Stability Analysis of a Pressure Compensator for Flow-Control Valve [J]. Journal of Shanghai Jiaotong University, 2011, 45(04): 561-564.
[12]	ZHU Zhi-Xia-1, LI Bei-2. Wave-current Numerical Model for Shanghai Nanhuizui Inning Project [J]. Journal of Shanghai Jiaotong University, 2011, 45(04): 590-596.