环境约束可重构机械臂模块化力/位置控制

摘要/Abstract

摘要： 针对受环境约束的可重构机械臂系统，提出了一种自适应神经网络模块化力/位置控制方法.利用雅克比矩阵将机械臂末端与环境接触力映射到各关节，将系统动力学模型描述成一组通过耦合力矩相关联的子系统集合，通过控制各子系统的位置和力矩来达到控制末端执行器位置和接触力的目的.利用神经网络估计可重构机械臂系统的非线性项和交联项，通过自适应更新律在线估计神经网络权值函数，并引入滑模控制项补偿估计误差，从而保证闭环系统渐近稳定.最后，在不改变控制器参数的条件下对2个不同构形的2自由度可重构机械臂进行数值仿真，结果验证了所设计控制器的有效性.

关键词: 可重构机械臂；环境约束；模块化控制；力/位置控制；神经网络

Abstract: This paper proposed an adaptive neural network modular position/force control method for environmental constrained reconfigurable manipulator. Mapping the endpoint force of the reconfigurable manipulator to each joint module, describe the entire dynamic model by a set of interconnected subsystems by coupling torques, and the position and contact force of the endpoint should be obtained by controlling the angle and torque of each subsystem. By virtue of the neural networks, the nonlinear and interconnected items are estimated, and the weights of these neural networks can be adaptively updated on line, meanwhile, the estimated errors are removed by a sliding mode control item, and the stabiltiy of the closedloop system should be granteed. Finally, the numerical simulation on two different 2DOF reconfigurable manipulators shows the effectiveness of the proposed method without changing control parameters.

Key words: reconfigurable manipulator； environmental constraint； modular control； position/force control； neural network

中图分类号:

TP 24

李元春1，宋扬2，赵博1,3. 环境约束可重构机械臂模块化力/位置控制[J]. 上海交通大学学报, 2017, 51(6): 709-714.

LI Yuanchun1,SONG Yang2,ZHAO Bo1,3. Modular Position/Force Control for
Environmental Constrained Reconfigurable Manipulator[J]. Journal of Shanghai Jiao Tong University, 2017, 51(6): 709-714.

参考文献

［1］ROEHR T M, CORDES F, KIRCHNER F. Reconfigurable integrated multirobot exploration system (RIMRES): Heterogeneous modular reconfigurable robots for space exploration ［J］. Journal of Field Robotics, 2014, 31(1): 334.
［2］COPPOLA G, ZHANG D, LIU K. A 6DOF reconfigurable hybrid parallel manipulator ［J］. Robotics and ComputerIntegrated Manufacturing, 2014, 30(2): 99106.
［3］RUSSO S, HARADA K, RANZANI T, et al. Design of a robotic module for autonomous exploration and multimode locomotion ［J］. IEEE/ASME Transactions on Mechatronics, 2013, 18(6): 17571766.
［4］HARADA K, OETOMO D, SUSILO E, et al. A reconfigurable modular robotic endoluminal surgical system: Vision and preliminary results ［J］. Robotica, 2010, 28(2): 171183.
［5］AHN H S, BEAK Y M, SA I K, et al. Design of reconfigurable heterogeneous modular architecture for service robots ［C］∥2008 IEEE/RSJ International Conference on Intelligent Robots and Systems. Nice, France: IEEE, 2008: 13131318.
［6］BIGLARBEGIAN M, MELEK W W, MENDEL J M. Design of novel interval type2 fuzzy controllers for modular and reconfigurable robots: theory and experiments ［J］. IEEE Transactions on Industrial Electronics, 2011, 58(4): 13711384.
［7］SUN T, SONG Y, LI Y, et al. Workspace decomposition based dimensional synthesis of a novel hybrid reconfigurable robot ［J］. Journal of Mechanisms and Robotics, 2010, 2(3): 191220.
［8］HERRERO S, MANNHEIM T, PRAUSE I, et al. Enhancing the useful workspace of a reconfigurable parallel manipulator by grasp point optimization ［J］. Robotic and ComputerIntegrated Manufacturing, 2015, 31: 5160.
［9］LI Z, MELEK W W, CLARK C. Decentralized robust control of robot manipulators with harmonic drive transmission and application to modular and reconfigurable serial arms ［J］. Robotica, 2009, 27(2): 291302.
［10］赵博, 李元春. 基于信号重构的可重构机械臂主动分散容错控制［J］. 自动化学报, 2014, 40(9): 19421950.
ZHAO Bo, LI Yuanchun. Signal reconstruction based active decentralized fault tolerant control for reconfigurable manipulators ［J］. Acta Automatica Sinica, 2014, 40(9): 19421950.
［11］ZHAO Bo, LI Chenghao, MA Tianhao, et al. Multiple faults detection and isolation via decentralized sliding mode observer for reconfigurable manipulator ［J］. Journal of Electrical Engineering & Technology, 2015, 10(6): 23932405.
［12］VLADAREANU L, ION I. New approaches on modular walking robots with forceposition hybrid control ［J］. Revue Roumaine Des Sciences Techniques Série de Mécanique Appliquée, 2010, 52: 167182.
［13］AHMAD S, ZHANG H, LIU G. Multiple working mode control of dooropening with a mobile modular and reconfigurable robot ［J］. IEEE/ASME Transactions on Mechatronics, 2013, 18(3): 833844.
［14］LEE W. Proposition of reconfigurable wall climbing robot using 6DOF force torque sensor based on flexible structure for real environment ［C］∥2013 13th International Conference on Control, Automation and Systems. Gwangju, South Korea: IEEE, 2013: 18021806.
［15］ZHAO B, LI Y C. Local joint information based active fault tolerant control for reconfigurable manipulator ［J］. Nonlinear Dynamics, 2014, 77(3): 859876.

[1]	赵子任1, 杜世昌1, 黄德林1, 任斐2, 梁鑫光2. 多工序制造系统暂态阶段产品质量#br# 马尔科夫建模与瓶颈分析[J]. 上海交通大学学报, 2017, 51(10): 1166-1173.
[2]	周鹏辉, 马红占, 陈东萍, 陈梦月, 褚学宁. 基于模糊随机故障模式与影响分析的#br# 产品再设计模块识别[J]. 上海交通大学学报, 2017, 51(10): 1189-1195.
[3]	李昌玺1, 2, 周焰1, 林菡3, 李灵芝1, 郭戈1. 基于MIMOFNN模型的弹道导弹目标#br# 时空序贯融合识别方法[J]. 上海交通大学学报, 2017, 51(9): 1138-.
[4]	冯明月, 何明浩, 韩俊, 郁春来. 基于协方差拟合旋转不变子空间信号参数#br# 估计算法的高分辨到达角估计[J]. 上海交通大学学报, 2017, 51(9): 1145-.
[5]	杨平1，盛杰1，王禹程2，李柱永1，金之俭1，洪智勇1. YBa2Cu3O7δ超导带材非均匀性对失超传播特性的影响[J]. 上海交通大学学报（自然版）, 2017, 51(9): 1090-1096.
[6]	王星, 周一鹏, 田元荣, 陈游, 周东青, 贺继渊. 基于改进遗传算法和SinChirplet原子的调频#br# 雷达信号稀疏分解[J]. 上海交通大学学报, 2017, 51(9): 1124-1130.
[7]	张良俊1, 2, 李晓慈1, 吴静怡1, 蔡爱峰1. 大型空间展开机构微重力环境模拟#br# 悬吊装置热结构耦合分析[J]. 上海交通大学学报, 2017, 51(8): 954-961.
[8]	夏海亮1, 2, 刘亚坤1, 2, 刘全桢3, 刘宝全3, 傅正财1, 2. 长持续时间雷电流分量作用下电极形状#br# 对金属烧蚀特性的影响[J]. 上海交通大学学报, 2017, 51(8): 903-908.
[9]	谷家扬, 谢玉林, 陶延武, 黄祥宏, 吴介. 新型浮式钻井生产储油平台#br# 涡激运动数值模拟及试验研究 [J]. 上海交通大学学报, 2017, 51(7): 878-885.
[10]	林达, 朱益佳, 魏小栋, 王志宇, 张武高. 喷油参数对聚甲氧基二甲醚/柴油发动机燃烧及其#br# 颗粒物排放的影响[J]. 上海交通大学学报, 2017, 51(7): 787-795.
[11]	孟庆阳1, 阎威武1, 胡勇1, 程建林1, 陈世和2, 张曦2. 基于子空间方法的超超临界机组#br# 过热蒸汽系统模型辨识[J]. 上海交通大学学报, 2017, 51(6): 672-678.
[12]	蒋华军a, 蔡艳a, b, 李超豪a, 李芳a, b, 华学明a, b. 基于改进Sobel算法的焊缝X射线图像#br# 气孔识别方法[J]. 上海交通大学学报, 2017, 51(6): 665-671.
[13]	董冠华,殷勤,殷国富,向召伟. 机床结合部耦合动刚度的辨识与建模[J]. 上海交通大学学报（自然版）, 2015, 49(09): 1263-1434.
[14]	谢启江，余海东. 硬岩掘进机刀盘载荷与撑靴接触界面刚度的耦合关系[J]. 上海交通大学学报（自然版）, 2015, 49(09): 1269-1275.
[15]	仲健林1，马大为1，任杰1，李士军2，王旭3. 基于平面应变假设的橡胶圆筒静态受压分析[J]. 上海交通大学学报（自然版）, 2015, 49(09): 1276-1280.