喷油参数对聚甲氧基二甲醚/柴油发动机燃烧及其#br#
颗粒物排放的影响

doi:10.16183/j.cnki.jsjtu.2017.07.004

摘要/Abstract

摘要： 在电控共轨高速柴油机试验台上，对比研究了分别以纯柴油和聚甲氧基二甲醚(PODE)/柴油(φPODE=20%)为燃料时，喷射压力、预喷相位和主喷相位等喷油参数对发动机燃烧及其颗粒物排放特性的影响.结果表明：当喷射压力增大时，预喷燃料放热相位提前，预喷燃烧放热率幅值降低，主喷放热相位提前，最高爆压升高，积聚模态颗粒物排放显著降低，柴油发动机在小负荷下的核模态颗粒物排放大幅升高；当预喷相位提前时，预喷放热相位略微提前且峰值下降，引起小负荷工况下的主喷放热相位延迟，燃烧放热率峰值显著增大，缸压降低，增加了柴油发动机的核模态颗粒物排放而降低了积聚模态颗粒物的排放，且受发动机负荷影响明显；当主喷相位提前时，缸压峰值增大、放热相位提前，使得低负荷下的颗粒物排放升高，高负荷下的颗粒物排放降低；掺混PODE燃料后，柴油发动机的核模态颗粒物排放增大的趋势得到有效抑制.

关键词: , 柴油发动机；聚甲氧基二甲醚；缸内燃烧；颗粒物；排放

Abstract: The research tested the effect of fuel supply parameters on combustion and particle emission characteristics on a diesel engine fueled with neat diesel and blends of polyoxymethylene dimethyl ethers (PODE)/diesel (φPODE=20%). The results showed that the increase of common rail pressure could cause advanced main fuel heat release, higher peak incylinder pressure and higher mean gas temperature; the increased common rail pressure would decrease accumulation mode particle (AMP) emission, but would increase nucleation mode particle (NMP) emission under lightduty mode. The advanced pilot injection timing would lower the pilot fuel heat release, and improve the main injection heat release under low load; the advanced pilot injection timing would effectively reduce the AMP number concentration, but cause obvious NMP number increase. The advanced main injection timing directly shifted the main fuel heat release rate and caused an advanced, increased pressure peak; earlier main injection timing would cause lower AMP number concentration and higher NMP emission under lowduty mode, and obtained opposite results under highduty mode. The introduction of PODE could amplify the positive effect of fuel supply parameters on particle emissions and suppress the NMP emission to a certain extent.

Key words: diesel engine, polyoxymethylene dimethyl ethers (PODE), incylinder combustion, particulate matter, emission

中图分类号:

TK 42

林达, 朱益佳, 魏小栋, 王志宇, 张武高. 喷油参数对聚甲氧基二甲醚/柴油发动机燃烧及其#br# 颗粒物排放的影响[J]. 上海交通大学学报, 2017, 51(7): 787-795.

LIN Da, ZHU Yijia, WEI Xiaodong, WANG Zhiyu, ZHANG Wugao. Combustion and Particle Emission Characteristics Affected by#br# Fuel Supply Parameters for a Diesel Engine Fuelled with#br# Polyoxymethylene Dimethyl Ethers/Diesel[J]. Journal of Shanghai Jiao Tong University, 2017, 51(7): 787-795.

参考文献

［1］WANG J X, WU F J, XIAO J H, et al. Oxygenated blend design and its effects on reducing diesel particulate emissions［J］. Fuel, 2009, 88: 20372045.
［2］BURGER J, SIEGERT M, STROFER E, et al. Poly (oxymethylene) dimethyl ethers as components of tailored diesel fuel: Properties, synthesis and purification concepts［J］. Fuel, 2010, 89(11): 33153319.
［3］SONG J, CHENKKACHORN K, WANG J, et al. Effect of oxygenated fuel on combustion and emissions in a lightduty turbo diesel engine［J］. Energy & Fuels, 2002, 16(2): 294301.
［4］肖潇, 郑轶, 王云芳, 等. 聚甲氧基二甲醚 (PODE) 与柴油的互溶性研究［J］. 柴油机, 2015, 37(3): 2428.
XIAO Xiao, ZHENG Yi, WANG Yunfang , et al. Research on compatibility of PODE and diesel fuel［J］. Diesel Engine, 2015, 37(3): 2428.
［5］王志, 刘浩业, 张俊, 等. 聚甲氧基二甲醚与柴油混合燃料的燃烧与排放特性［J］. 汽车安全与节能学报, 2015, 6(2): 191197.
WANG Zhi, LIU Haoye, ZHANG Jun, et al. Combustion and emission characteristics of diesel engines fueled by polyoxymethylene dimethyl ethers (PODEn)［J］. Automotive Safety and Energy, 2015, 6(2): 191197.
［6］杨皓, 李兴虎, 牟鸣飞, 等. 柴油/聚甲氧基二甲醚混合燃料的柴油机性能与排放试验［J］. 汽车安全与节能学报, 2015, 6(3): 280285.
YANG Hao, LI Xinghu, MU Mingfei, et al. Experiments on the performances and emissions of diesel engine fueled with diesel/polyoxymethylene dimethyl ethers blends［J］. Automotive Safety and Energy, 2015, 6(3): 280285.
［7］PELLEGRINI L, MARCHIONNA M, PATRINI R, et al. Emission performance of neat and blended polyoxymethylene dimethyl ethers in an old lightduty diesel car ［EB/OL］. ［20161031］. https:∥saemobilus.sae.org/content/2013011035.
［8］PELLEGRINI L, MARCHIONNA M, PATRINI R, et al. Combustion behavior and emission performance of neat and blended polyoxymethylene dimethyl ethers in a lightduty diesel engine［EB/OL］. ［20161031］. https:∥saemobilus.sae.org/content/2012011053.
［9］张向京, 武朋涛, 蒋子超,等. 聚甲醛二甲醚反应热力学分析［J］. 化学工程, 2015, 43(4):3944.
ZHANG Xiangjing, WU Pengtao, JIANG Zichao, et al. Thermodynamic analysis on synthesis of polyoxymethylene dimethyl ethers［J］. Chemical Engineering, 2015, 43(4): 3944.
［10］张武高, 魏小栋, 林达, 等. 聚甲氧基二甲醚对发动机超细颗粒排放特性影响的试验研究［J］. 汽车安全与节能学报, 2016,7(3): 330336.
ZHANG Wugao, WEI Xiaodong, LIN Da, et al. Experimental study on the influence of polyoxymethylene dimethyl ethers (PODE) on ultrafine particle emission of a compression ignition engine［J］. Automotive Safety and Energy, 2016,7(3): 330336.
［11］HUSSEIN T. Indoor and outdoor aerosol particle size characterization in Helsinki［R］. Helsinki, Finland: University of Helsinki, 2005.

编辑推荐 0

Metrics

阅读次数

全文

HTML			PDF

最新录用	在线预览	正式出版	最新录用	在线预览	正式出版
0	0	0	5	0	93

来源	本网站	其他网站

次数	30	68
比例	31%	69%

摘要

938

最新录用	在线预览	正式出版

88	0	850

来源	本网站	其他网站

次数	494	444
比例	53%	47%

[1]	王晶, 王伟, 王爱武. 稳控装置在海油平台电网的应用[J]. 海洋工程装备与技术, 2024, 11(1): 65-69.
[2]	林浩安, 陈俐. 面向偏航最小的风帆助航船攻角优化策略研究[J]. 海洋工程装备与技术, 2024, 11(1): 1-9.
[3]	周烨琦, 王锐. 海底沙波对光缆铺设放缆余量计算的影响[J]. 海洋工程装备与技术, 2023, 10(4): 135-139.
[4]	王聚团, 戚晓宁, 黄志明. 水下生产管汇测试技术及其改进研究[J]. 海洋工程装备与技术, 2022, 9(2): 43-49.
[5]	袁振钦, 邹科, 孙亚峰, 刘刚, 屈衍, 李居跃. 基于时域分析法的动态电缆疲劳分析[J]. 海洋工程装备与技术, 2022, 9(2): 50-55.
[6]	尹彦坤, 易涤非. 半潜式生产平台船体结构关键节点工程临界评估[J]. 海洋工程装备与技术, 2022, 9(1): 52-57.
[7]	王娟, 杨明旺, 郑茂尧, 刘凌云, 赵立君. 高强钢在大型半潜式平台组块建造中的应用[J]. 海洋工程装备与技术, 2022, 9(1): 27-31.
[8]	陈欣, 赵晓磊, 王立坤, 肖德明, 张腾月. 深水大型吸力锚建造技术研究[J]. 海洋工程装备与技术, 2022, 9(1): 32-36.
[9]	ZHANG Shengfa (张胜发), TANG Na (唐纳), SHEN Guofeng (沈国峰), WANG Han (王悍), QIAO Shan (乔杉). Universal Software Architecture of Magnetic Resonance-Guided Focused Ultrasound Surgery System and Experimental Study[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(4): 471-481.
[10]	MA Qunsheng (马群圣), CEN Xingxing (岑星星), YUAN Junyi (袁骏毅), HOU Xumin (侯旭敏). Word Embedding Bootstrapped Deep Active Learning Method to Information Extraction on Chinese Electronic Medical Record[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(4): 494-502.
[11]	安庆升, 孙立东, 武秋生. 碳纤维增强复合材料发射筒设计研究[J]. 空天防御, 2021, 4(2): 13-19.
[12]	KONG Xiangqiang (孔祥强), MENG Xiangxi (孟祥熙), LI Jianbo (李见波), SHANG Yanping (尚燕平), CUI Fulin (崔福林) . Comparative Study on Two-Stage Absorption Refrigeration Systems with Different Working Pairs[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(2): 155-162.
[13]	ZHUANG Weimin (庄蔚敏), WANG Pengyue (王鹏跃), AO Wenhong (熬文宏), CHEN Gang (陈刚) . Experiment and Simulation of Impact Response of Woven CFRP Laminates with Different Stacking Angles[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(2): 218-230.
[14]	HUANG Ningning (黄宁宁), MA Yixin (马艺馨), ZHANG Mingzhu (张明珠), GE Hao (葛浩), WU Huawei (吴华伟). Finite Element Modeling of Human Thorax Based on MRI Images for EIT Image Reconstruction[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(1): 33-39.
[15]	ZHOU Xuhui (周旭辉), ZHANG Wenguang (张文光), XIE Jie (谢颉). Effects of Micro-Milling and Laser Engraving on Processing Quality and Implantation Mechanics of PEG-Dexamethasone Coated Neural Probe[J]. J Shanghai Jiaotong Univ Sci, 2021, 26(1): 1-9.