线电极电火花磨削运丝系统设计及线电极有效加工区位置波动的试验

上海交通大学学报（自然版） ›› 2015, Vol. 49 ›› Issue (01): 23-30.

线电极电火花磨削运丝系统设计及线电极有效加工区位置波动的试验

王燕青1,2，白基成1，朱国征1，张恒1

（1. 哈尔滨工业大学机电工程学院, 哈尔滨 150001； 2. 中航通飞研究院有限公司第四研究室, 广东珠海 519030）

收稿日期:2014-02-24
基金资助:
国家高技术研究发展计划（863）项目（2007AA04Z345），国家自然科学基金资助项目（51175120）

Design of a Wire Transport System and Position Fluctuations of Discharge Area in Wire Electrode in WEDG

WANG Yanqing1,2，BAI Jicheng1，ZHU Guozheng1，ZHANG Heng1

(1. School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001, China;2. No.4th Research Office, AVIC General Aircraft Research Institute Co. Ltd., Zhuhai 519030, Guangdong, China)

Received:2014-02-24

摘要/Abstract

摘要：

摘要：为了减小线电极电火花磨削中线电极有效加工区位置的波动，建立了运丝系统多自由度振动模型，分析了滚轮的直径和质量、相邻滚轮间线电极的材料、长度和直径对运丝系统振动固有频率的影响，将仿真分析结果用于指导运丝系统设计，以提高运丝系统的固有频率并减小线电极有效加工区发生振动的频率；通过试验研究了线电极运丝速度、线电极在导向轮上的包角及线电极张力对线电极有效加工区位置波动的影响规律，并用于确定最佳加工参数；同时，利用所设计的线电极磨削装置加工出直径为(50±1) μm的微细轴.结果表明，所设计的线电极磨削装置及试验获得的最佳加工参数可用于高尺寸精度的微细轴加工.

关键词: 线电极电火花磨削, 运丝系统, 多自由度振动模型, 有效加工区, 微细轴

Abstract:

Abstract： A multidegree of freedom vibration model for wire transport system was developed to analyze the effects of material and diameters of wire electrode, diameters and mass of wheels, and the length of wire electrode between two adjacent wheels on the natural frequency of the wire transport system. And the obtained conclusions through simulation analysis were used to increase the natural frequency of the wire transport system, thereby reducing the possibility of resonance and decreasing the position fluctuations of discharge area. The effects of wire running speeds, wrap angles of wire electrode on wheel guide, and wire electrode tension on the position fluctuation rang of discharge area were experimentally studied. Finally, a micro shaft with a diameter of (50±1) μm was successfully fabricated. The experimental results show that the designed wire electrical discharge grinding(WEDG) device and optimal parameters obtained through experimental study can be used to process micro shafts with high dimensional accuracy.

Key words: wire electrical discharge grinding (WEDG), wire transport system, multidegree of freedom vibration model, discharge area, micro shafts

中图分类号:

TG 661

王燕青1,2，白基成1，朱国征1，张恒1. 线电极电火花磨削运丝系统设计及线电极有效加工区位置波动的试验[J]. 上海交通大学学报（自然版）, 2015, 49(01): 23-30.

WANG Yanqing1,2，BAI Jicheng1，ZHU Guozheng1，ZHANG Heng1. Design of a Wire Transport System and Position Fluctuations of Discharge Area in Wire Electrode in WEDG[J]. Journal of Shanghai Jiaotong University, 2015, 49(01): 23-30.

参考文献

［1］Masuzawa T, Fujino M, Kobayashi K. Wire electrodischarge grinding for micromachining［J］. Annals of the CIRP, 1985, 34(1): 431434.

［2］Fujino M, Okamoto N, Masuzawa T. Development of multipurpose microprocessing machine［C］//Proc ISEMXI International Symposium on ElectroMachining. Lausanne: Presses Polytechniques Et Universitaires Romandes, 1995: 613620.

［3］Egashira K, Masuzawa T. Microultrasonic machining by the application of workpiece vibration［J］. Annals of the CIRP, 1999, 48(1): 131134.

［4］Sheu D Y, Cheng C C. Assembling ballended styli for CMM’s tactile probing heads on micro EDM［J］. The International Journal of Advanced Manufacturing Technology, 2013, 65(14): 485492.

［5］Sheu D Y. Multispherical probe machining by EDM Combining WEDG technology with onepulse electrodischarge ［J］. Journal of Materials Processing Technology, 2004, 149(13): 597603.

［6］Sun X Q, Masuzawa T, Fujino M. Micro ultrasonic machining and its applications in MEMS［J］. Sensors and Actuators A: Physical, 1996, 57(2): 159164.

［7］Morgan C J. Micro electrodischarge machining: techniques and procedures for micro fabrication ［D］. Lexington: University of Kentucky, 2004.

［8］Rees A, Dimov S S, Ivanov A, et al. Microelectrode discharge machining: Factors affecting the quality of electrodes produced on the machine through the process of wire electrodischarge machining［J］. Proceedings of the Institution of Mechanical Engineers. Part B: Journal of Engineering Manufacture, 2007, 221(3): 409418.

［9］Wu Y M. Automatic control for microelectrode fabrication in microEDM system ［D］. Yunlin: National Yunlin University of Science and Technology, 2001.

［10］Chang P Y. Application of taguchi methods for microelectrode fabrication automation in microEDM system ［D］. Yunlin: National Yunlin University of University of Science and Technology, 2003.

［11］Huang C S. Closed loop control for microelectrode fabrication automation ［D］. Yunlin: National Yunlin University of University of Science and Technology, 2005.

［12］pz T. Manufacturing of micro holes by using micro electric discharge machining ［D］. Ankara: Atilim University, 2008.

［13］Wang P W, Yang C S. Analysis and design of wire transport system in microwireelectronic discharge machining［J］. Journal of Micro and NanoManufacturing, 2013, 1(2): 02100610210069.第49卷第1期2015年1月上海交通大学学报JOURNAL OF SHANGHAI JIAO TONG UNIVERSITYVol.49 No.1Jan. 2015

[1]	邱明波, 史璟云, 俞晓春, 刘志东. 比例-积分-微分压力控制的放电雾化烧蚀磨削加工方法[J]. 上海交通大学学报, 2019, 53(1): 111-117.
[2]	刘晓1，陈吉朋2，顾琳2，陈风帆1，王炜1. 50%SiCp/Al复合材料的电弧铣削与铣磨组合加工[J]. 上海交通大学学报（自然版）, 2018, 52(2): 222-227.
[3]	梁速, 赵万生, 康小明. 基于可编程运动控制器的电火花加工高速抬刀控制系统 [J]. 上海交通大学学报（自然版）, 2012, 46(09): 1476-1481.
[4]	梁速, 赵万生, 康小明. 基于Linux的五轴联动电火花加工数控系统[J]. 上海交通大学学报（自然版）, 2012, 46(07): 1097-1102.
[5]	杨凯, 顾琳, 薛荣, 张发旺, 赵万生. 喷雾电火花铣削加工工艺的研究 [J]. 上海交通大学学报（自然版）, 2012, 46(07): 1021-1025.