转轮式全热回收器的数学模型与变工况性能分析

摘要/Abstract

摘要：

摘要：
建立了转轮式全热回收器的数学模型，与现有文献对比验证了该模型的正确性，并利用此模型研究了迎面风速、新排风比、新风温度（含湿量不变或相对湿度不变）、新风含湿量的变化对转轮热回收效率的影响.结果表明，随迎面风速的增大，转轮的显热效率、潜热效率与全热效率均降低；随排风量与新风量之比增大，或新风温度的升高（相对湿度不变时），转轮的显热效率、潜热效率与全热效率均增大；随新风温度的升高（含湿量不变时），转轮的显热效率增大，潜热效率与全热效率降低；随新风含湿量增大，转轮的显热效率不变，潜热效率与全热效率升高.

关键词: 转轮式全热回收器, 数学模型, 热回收效率, 变工况

Abstract:

The mathematical model of enthalpy recovery wheel was built and verified by comparison with existing literatures, based on which, the effects of air velocity, proportion of fresh air and exhaust air, fresh air temperature (when humidity ratio is constant or relative humidity is constant), fresh air humidity ratio on the heat recovery efficiency of enthalpy recovery wheel were investigated. The results show that the sensible heat efficiency, latent heat efficiency and total heat efficiency of enthalpy recovery wheel decrease with increasing of air velocity; when proportion of fresh air and exhaust air increases, or fresh air temperature increases (relative humidity is constant), and the sensible heat efficiency, latent heat efficiency and total heat efficiency increase, too; with increasing of fresh air temperature (humidity ratio is constant ), the sensible heat efficiency increases, while the latent heat efficiency and total heat efficiency decrease; when fresh air humidity ratio increases, the sensible heat efficiency remains constant, while the latent heat efficiency and total heat efficiency increase.

Key words: enthalpy recovery wheel, mathematical model, heat recovery efficiency, variable condition

中图分类号:

TU 831

方继华,谷波,张杰. 转轮式全热回收器的数学模型与变工况性能分析[J]. 上海交通大学学报（自然版）, 2014, 48(06): 809-815.

FANG Jihua，GU Bo，ZHANG Jie. Mathematical Model and Performance Analysis with Variable Condition of Enthalpy Recovery Wheel[J]. Journal of Shanghai Jiaotong University, 2014, 48(06): 809-815.

参考文献

［1］钱以明，董启平.转轮式全热交换器结构参数的优化［J］.制冷学报，1990(4)：612.

QIAN Yiming, DONG Qiping. The optimization of the structural dimensions for rotary total heat exchanger ［J］. Journal of Refrigeration, 1990(4):612.

［2］江亿.温湿度独立控制空调系统［M］.北京：中国建筑工业出版社，2006.

［3］Nóbrega C E L, Brum N C L. Modeling and simulation of heat and enthalpy recovery wheels ［J］. Energy, 2009, 34(12): 20632068.

［4］Wu Z, Melnik R V N, Borup F. Modelbased analysis and simulation of regenerative heat wheel ［J］. Energy and Buildings, 2006, 38(5):502514.

［5］Wei R, Ming Q, Horton W T. Modeling analysis of an enthalpy recovery wheel with purge air ［J］.

International Journal of Heat and Mass Transfer, 2012, 55(1718): 46654672.

［6］Sphaier L A, Worek W M. The effect of axial diffusion in desiccant and enthalpy wheels ［J］.

International Journal of Heat and Mass Transfer, 2006, 49(78): 14121419.

［7］腊栋，蔡世佳，代彦军，等.基于不同干燥剂的焓轮式全热回收器特性数值模拟［J］.化工学报，2008，59(S2)：6469.

LA Dong, CAI Shijia, DAI Yanjun, et al. Numerical simulation of characteristics of enthalpy recovery wheel with different desiccants ［J］. Journal of Chemical Industry and Engineering, 2008, 59(S2):6469.

［8］Jeong J W, Mumma S A. Practical thermal performance correlations for molecular sieve and silica gel loaded enthalpy wheels ［J］. Applied Thermal Engineering, 2005, 25(56):719740.

［9］Zhang L Z, Niu J L. Performance comparisons of desiccant wheels for air dehumidification and enthalpy recovery ［J］. Applied Thermal Engineering, 2002, 22(12):13471367.

［10］潘少华，祝刚.全热回收转轮的工作特性分析［J］.制冷空调与电力机械，2007，28(5)：7678.

PAN Shaohua, ZHU Gang. Character analysis on the running wheels of air ventilator with total thermal recovery ［J］. Refrigeration Air Conditioning & Electric Power Machinery, 2007, 28(5):7678.

［11］陆冬梅.转轮全热交换器对空调箱运行能耗的影响［J］.山西建筑，2010，36(9)：192193.

LU Dongmei. Rotate wheel heat exchanger’s influence on air conditioner’s operation energy consumption ［J］. Shanxi Architecture, 2010, 36(9):192193.

［12］张学军，代彦军，王如竹.蜂窝式除湿转轮的传热传质数学模型及其试验验证［J］.机械工程学报，2005，41(1)：8287.

ZHANG Xuejun, DAI Yanjun, WANG Ruzhu. Heat mass transfer model of a honeycombed desiccant wheel and experiment ［J］. Chinese Journal of Mechanical Engineering, 2005, 41(1):8287.

［13］PlaBarby F E, Vliet G C. Rotary bed solid desiccant drying: An analytical and experimental investigation［C］//ASME/AICHE 18th National Heat Transfer Conference. San Diego, USA:CA, 1979:78.

［14］陆耀庆.实用供热空调设计手册［M］.2版.北京：中国建筑工业出版社，2007.

［15］Simonson C J, Besant R W. Energy wheel effectiveness. Part II: Correlations ［J］. International Journal of Heat and Mass Transfer, 1999, 42(12):21712185.

[1]	马航宇, 周笛, 卫宇杰, 吴伟, 潘尔顺. 变工况下基于自适应深度置信网络的轴承智能故障诊断[J]. 上海交通大学学报, 2022, 56(10): 1368-1377.
[2]	王泽坤, 张福曦. 3D电子封装锡晶须建模与实验验证[J]. 上海交通大学学报, 2021, 55(11): 1445-1452.
[3]	王伟, 李奥特, 于军力. 基于目标流量拟合的微型燃烧室流量分配设计方法[J]. 上海交通大学学报, 2020, 54(9): 1000-1006.
[4]	张维凯，胡鹏. 异重流水卷吸经验式不确定性对层平均数学模型的影响[J]. 上海交通大学学报, 2020, 54(1): 35-42.
[5]	梁笑阳,马宁,刘晗,顾解忡. 回转体潜器在循环水槽中垂直面大攻角操纵性试验[J]. 上海交通大学学报, 2019, 53(12): 1395-1403.
[6]	胡明，王炅，范一清. 磁流变液孔口出流数学模型[J]. 上海交通大学学报（自然版）, 2017, 51(9): 1065-1070.
[7]	吴利杰, 于娟, 石建省, 王成敏, 毕志伟, 郭娇. 长尺度气候变化下土壤钾素演变规律的研究——以泾河中游将军村黄土剖面为例[J]. 上海交通大学学报(农业科学版), 2016, 34(1): 69-73.
[8]	朱志夏. 非结构化网格嵌套波浪数值模拟[J]. 上海交通大学学报（自然版）, 2016, 50(01): 152-157.
[9]	孙旭东，谷波，田镇. 变工况条件下的纯电动车热泵系统火用性能分析[J]. 上海交通大学学报（自然版）, 2015, 49(05): 608-613.
[10]	黄家瀚，王新杰，王炅. 基于光致形变材料的光驱动微夹钳[J]. 上海交通大学学报（自然版）, 2014, 48(12): 1681-1687.
[11]	陈侠，张婧，徐光延. 移动威胁下的无人机三维航迹规划[J]. 上海交通大学学报（自然版）, 2014, 48(10): 1400-1405.
[12]	梁任1，余岳峰1，陈亮乐2，邓志强2，黄云2. 螺杆膨胀机有机朗肯循环系统的变工况特性[J]. 上海交通大学学报（自然版）, 2014, 48(09): 1291-1296.
[13]	曹卫华1,2，蔡伊青2，袁艳1,2，吴敏1,2. 烧结余热回收系统效率计算及参数动态优化[J]. 上海交通大学学报（自然版）, 2014, 48(07): 1046-1052.
[14]	刘振宇，陈娅琪，吴慧英. 变工况空间太阳电池翼在轨热变形分析[J]. 上海交通大学学报（自然版）, 2013, 47(11): 1762-1766.
[15]	卫琛喻, 臧述升, 葛冰, 蒲强. 小型燃气轮机湿空气透平循环变工况性能[J]. 上海交通大学学报（自然版）, 2013, 47(03): 346-351.