螺旋桨空化初生的判定和空化斗的数值分析

摘要/Abstract

摘要： 摘要：
为了实现空化多相流模拟在螺旋桨空化初生和空化斗预报中的应用，采用改进Sauer空化模型和修正剪切应力输运(SST)湍流模型，对NSRDC4381桨的叶背和叶面片空化初生、梢涡空化初生和空化斗底线特征进行了模拟、校验和分析，提出了“当σ>σi时，叶梢截面压力系数分布不再改变”的空化初生判定准则，并分析了其适用范围. 同时，将空化斗由传统的三区细分为五区，以更准确地描述不同工况点的桨叶空化状态. 结果表明，在设计和非设计进速系数下，预报桨叶叶背和叶面不同叶截面的初生空化数均与实验值吻合较好；模拟梢涡空化初生再现了局部梢涡空化和导边梢涡空化同时存在的现象，证明了分别用叶背07 R截面和叶面04 R截面的片空化初生曲线来表征叶背和叶面可视梢涡空化初生的合理性. 空化初生判定准则适用于空化斗底线上方的叶背和叶面片空化区. 将空化斗底线下方区域进一步细分为叶背03 R至叶梢的片空化区以及叶背与叶面同时片空化区，以更好地在工程中应用空化斗来描述桨叶空化形态和求取空化航态的航速.

关键词: 螺旋桨, 空化初生, 空化斗, 空化模型, 湍流模型

Abstract: To apply the cavitation multiphase simulation for propeller cavitation inception and inception bucket prediction, the improved Sauer cavitation model and modified shear stress transport turbulence model were used to predict the NSRDC 4381 propellers back and face sheet cavitation inception, tip vortex cavitation inception and inception bucket bottom line characteristics. A rule to determine the cavitation inception was presented printed as ‘when σ>σi, the pressure coefficient of the tip blade section is unchangeable and its application region on the bucket was limited also. Based on it, the inception bucket was partitioned more nicely from traditional three regions to five at last so to depict the blade cavitation stage under different conditions more precisely. The results show that, under design and nondesign conditions, the predicted inception cavitation indexes of the back and faces blade section all agree well with the experiment. The simulated tip vortex cavitation inception represents the phenomenon of local tip vortex and leading edge tip vortex combination, and verifies the reasonableness of using the sheet cavitation inception curves of 07 R section on the back and 04 R section on the face to stand for the back and faces visual tip vortex inception respectively. The determination rule is valid for both back and face sheet cavitation region up the bottom line on the bucket. The region under the bottom line on the bucket can be partitioned as back sheet cavitation lying 03 R to tip on the blade surface and back and face sheet cavitation existing simultaneously in addition, so to sever the engineering better for using the five regions to depict the propeller cavitation and calculate the cavitation ship speed.

Key words: propeller, cavitation initial inception, inception bucket, cavitation model, turbulence model

中图分类号:

U664.34

杨琼方a, 王永生a, 张志宏b. 螺旋桨空化初生的判定和空化斗的数值分析[J]. 上海交通大学学报（自然版）, 2012, 46(03): 410-416.

YANG Qiong-Fang-a, WANG Yong-Sheng-a, ZHANG Zhi-Hong-b. Determination of Propeller Cavitation Initial Inception and Numerical Analysis of the Inception Bucket[J]. Journal of Shanghai Jiaotong University, 2012, 46(03): 410-416.

参考文献

［1］Liu D C, Hong F W, Zhao F, et al. The CFD analysis of propeller sheet cavitation［C］//Proceedings of 8th International Conference on Hydrodynamics. Nantes France: Ecole Centrale de Nantes Fluid Mechanics Laboratory, 2008: 16.
［2］Lindau J W, Boger D A, Medvitz R B, et al. Propeller cavitation breakdown analysis［J］. ASME Journal of Fluids Engineering, 2005, 127(5): 9951002.
［3］Lindau J W, Moody W L, Kinzel M P, et al. Computation of cavitating flow through marine propulsors［C］//First International Symposium on Marine Propulsors. Norway: Norwegian Marine Technology Research Institute, 2009: 168177.
［4］Kim S E. Multiphase CFD simulation of turbulent cavitating flows in and around marine propulsors［C］//Open Source CFD International Conference 2009. Spain: IconCFD Inc, 2009: 131.
［5］杨琼方, 王永生, 张志宏. 螺旋桨叶截面空化模拟数值模型的改进与评估［J］. 北京理工大学学报, 2011, 31(12): 14011407.
YANG Qiongfang, WANG Yongsheng, ZHANG Zhihong. Improvement and evaluation of numerical model for viscous simulation of cavitating flow around propeller blade section［J］. Transactions of Beijing Institute of Technology, 2011, 31(12): 14011407.
［6］杨琼方, 王永生, 张志宏.螺旋桨空化崩溃性能图谱的多相流模拟与校验［J］. 华中科技大学学报(自然科学版), 2012, 40(2): 719723.

YANG Qiongfang, WANG Yongsheng, ZHANG Zhihong. Prediction of propeller cavitating breakdown performance maps based on cavitation multiphase viscous simulation［J］. Journal of Huazhong University of Science and Technology （Natural Science Edition）, 2012, 40(2): 719723.
［7］Szantyr J A. Scale effects in cavitation experiments with marine propeller models［J］. Polish Maritime Research, 2006, 4: 310.
［8］Gindroz B, Bailo G, Matera F, et al. Influence of cavitation nuclei on the cavitation bucket when predicting the fullscale behavior of a marine propeller［C］//Proceedings of 21st Symposium on Naval Hydrohydamics. USA: The National Academics Press, 1997: 839850.
［9］Boswell R J. Design, cavitation performance and openwater performance of a series of research skewed propellers, Report No. 3339［R］. Washington D C: Naval Ship Research and Development Center, 1971.
［10］Kuiper G, Terwisga T, Zondervan G, et al. Cavitation inception tests on a systematic series of twobladed propeller［C］//26th Symposium on Naval Hydrodynamics. Rome, Italy:［s.n.］, 2006.
［11］杨琼方, 王永生, 张志宏. 非均匀进流对螺旋桨空化水动力性能的影响［J］. 水动力学研究与进展（A辑）, 2011, 26(5): 538550.
YANG Qiongfang, WANG Yongsheng, ZHANG Zhihong. Effects of nonuniform inflow on propeller cavitation hydrodynamics［J］. Chinese Journal of Hydrodynamics, 2011, 26(5): 538550.
［12］Kuiper G. New developments around sheet and tip vortex cavitation on ships propellers［C］//Proceedings of 4th International Symposium on Cavitation(CAV2001). Pasadena: California Institute of Technology, 2001: 120.

编辑推荐

Metrics

阅读次数

全文

519

HTML			PDF

最新录用	在线预览	正式出版	最新录用	在线预览	正式出版
0	0	0	0	0	519

来源	本网站	其他网站

次数	26	493
比例	5%	95%

摘要

3858

最新录用	在线预览	正式出版

0	0	3858

来源	本网站	其他网站

次数	523	3335
比例	14%	86%

[1]	秦广菲, 姚慧岚, 张怀新. 螺旋桨脉动压力作用下自航船舶艉部振动数值研究[J]. 上海交通大学学报, 2022, 56(9): 1148-1158.
[2]	李鹏, 王超, 孙华伟, 郭春雨. 潜艇阻力及流场数值仿真策略优化分析[J]. 上海交通大学学报, 2022, 56(4): 506-515.
[3]	刘恒, 伍锐, 孙硕. 非均匀流场螺旋桨空泡数值模拟[J]. 上海交通大学学报, 2021, 55(8): 976-983.
[4]	吴利红, 封锡盛, 叶作霖, 李一平. 自主水下机器人强制自航下潜的类物理模拟[J]. 上海交通大学学报, 2021, 55(3): 290-296.
[5]	张宇, 王晓亮. 基于径向点插值方法的柔性螺旋桨气动弹性模拟[J]. 上海交通大学学报, 2020, 54(9): 924-934.
[6]	徐野, 熊鹰, 黄政. 双桨船螺旋桨空泡脉动压力的试验及数值研究[J]. 上海交通大学学报, 2020, 54(8): 831-838.
[7]	李清，于汉，杨德庆. 多类振动噪声源下舰船水下噪声的耦合声场计算方法[J]. 上海交通大学学报（自然版）, 2019, 53(2): 161-169.
[8]	黄福祥, 吴昌楠, 李想, 李新飞, 李隶辉, 阴炳钢. 动力定位船桨-桨干扰建模及分析[J]. 海洋工程装备与技术, 2019, 6(2): 536-543.
[9]	姚慧岚, 张怀新. 较低雷诺数下ITTC尺度效应换算方法的改进[J]. 上海交通大学学报, 2019, 53(1): 35-41.
[10]	傅慧萍a,b，李杰a. 轻载下的螺旋桨空化流场数值模拟[J]. 上海交通大学学报（自然版）, 2018, 52(6): 631-635.
[11]	倪问池1,2,康庄1,张橙1,张立健1. 运用修正剪应力输运湍流模型模拟双自由度涡激振动[J]. 上海交通大学学报（自然版）, 2017, 51(7): 819-825.
[12]	赵大刚1，郭春雨1，苏玉民1，豆鹏飞2，景涛1，张海鹏1. L型吊舱推进器直航及操舵工况水动力性能试验研究[J]. 上海交通大学学报（自然版）, 2017, 51(7): 812-818.
[13]	刘辉1,2，冯榆坤1,2，陈作钢1,2,3，代燚1,2,3，田喜民1,4. 船舶艏侧推器脉动压力数值计算[J]. 上海交通大学学报（自然版）, 2017, 51(3): 294-.
[14]	叶金铭，王威，于安斌，张凯奇. 抗空化扭曲舵的设计及其水动力性能分析[J]. 上海交通大学学报（自然版）, 2017, 51(3): 314-.
[15]	刘芬，陈丽,段登平. 多螺旋桨浮空器的抗饱和控制器设计[J]. 上海交通大学学报（自然版）, 2017, 51(2): 157-.