基于逆有限元法和网格映射的板材成型坯料优化

doi:10.16183/j.cnki.jsjtu.2019.11.016

上海交通大学学报 ›› 2019, Vol. 53 ›› Issue (11): 1389-1394.doi: 10.16183/j.cnki.jsjtu.2019.11.016

• 学报（中文） • 上一篇

基于逆有限元法和网格映射的板材成型坯料优化

张向奎，王洋，王长生，胡平

大连理工大学运载工程与力学学部；工业装备结构分析国家重点实验室，辽宁大连 116024

发布日期:2019-12-11
通讯作者: 王长生，男，讲师，主要研究方向为拟协调有限元和车身覆盖件板材冲压成型技术，E-mail: changsheng@dlut.edu.cn.
作者简介:张向奎(1976-)，男，辽宁省昌图县人，副教授，主要研究方向为汽车CAE软件平台技术，E-mail: zhangxk@dlut.edu.cn.
基金资助:
国家自然科学基金资助项目(11472071,11702055)

Blank Optimization for Sheet Metal Forming Using Inverse Finite Element Method and Mesh Mapping

ZHANG Xiangkui,WANG Yang,WANG Changsheng,HU Ping

Faculty of Vehicle Engineering and Mechanics; State Key Laboratory of Structural Analysis for Industrial Equipment, Dalian University of Technology, Dalian 116024, Liaoning, China

Published:2019-12-11

摘要/Abstract

摘要： 在金属板材成型中，坯料经拉延成型后得到无缺陷与无多余材料的零件，意味着坯料设计必须合理.由于坯料的非均匀流动和各向异性特性产生的凸耳与不均匀法兰，成型零件与目标零件存在形状差异.为获得合理的坯料，提出节点网格映射方法.结合逆有限元分析和增量分析，根据映射关系和材料点流动趋势优化坯料形状.为了验证提出的方法，分别对方盒件成型和某电动车B柱成型进行坯料设计.结果表明，对于较为复杂的工业零件，所提出的方法经过有限次优化后可得到合理坯料形状，所需的目标零件形状与采用合理坯料成型后的形状一致.

关键词: 逆有限元法; 坯料设计; 节点网格映射方法; 板料成型

Abstract: The transformation of the sheet into products without failure and excess of material in a sheet metal forming operation means that the blanks should be correctly designed. Due to the earing or non-uniform flange in sheet metal forming, caused by non-uniform material flow and planar anisotropy in the sheet, shape differences exist between the forming parts and target parts. In order to obtain a reasonable blank, the node mesh mapping method is proposed. Combining with the inverse finite element analysis and incremental analysis, the blank shape is optimized according to the mapping relationship and the flow tendency of material points. To test the proposed method, blank shape optimizations in the forming processes of a square box part and an electric car B-pillar are presented respectively. The results show that for more complex industrial parts, the method proposed in this paper can obtain a reasonable blank shape after a finite optimization, and the required shape of the target part is consistent with the shape after forming with a reasonable blank.

Key words: inverse finite element method; blank design; node mesh mapping method; sheet metal forming

中图分类号:

TG 386.4

张向奎，王洋，王长生，胡平. 基于逆有限元法和网格映射的板材成型坯料优化[J]. 上海交通大学学报, 2019, 53(11): 1389-1394.

ZHANG Xiangkui,WANG Yang,WANG Changsheng,HU Ping. Blank Optimization for Sheet Metal Forming Using Inverse Finite Element Method and Mesh Mapping[J]. Journal of Shanghai Jiaotong University, 2019, 53(11): 1389-1394.

参考文献

［1］朱明华, 王文斌, 鲍益东, 等. 飞机橡皮囊成形零件毛坯精确预示方法研究［J］. 航空学报, 2013, 34(3): 670-676. ZHU Minghua, WANG Wenbin, BAO Yidong, et al. Research on precise blank prediction method of aircraft part by rubber bladder forming［J］. Acta Aeronautica ET Astronautica Sinica, 2013, 34(3): 670-676. ［2］YANG C, LI P, FAN L X. Blank shape design for sheet metal forming based on geometrical resemblance［J］. Procedia Engineering, 2014, 81: 1487-1492. ［3］MOLE N, CAFUTA G, TOK B. A method for optimal blank shape determination in sheet metal forming based on numerical simulations［J］. Strojniki Vestnik-Journal of Mechanical Engineering, 2013, 59(4): 237-250. ［4］WANG H, YE F, CHEN L, et al. Sheet metal forming optimization by using surrogate modeling techniques［J］. Chinese Journal of Mechanical Engineering, 2017, 30(1): 22-36. ［5］GUO Y Q, BATOZ J L, NACEUR H, et al. Recent developments on the analysis and optimum design of sheet metal forming parts using a simplified inverse approach［J］. Computers & Structures, 2000, 78(1/2/3): 133-148. ［6］李晓达, 张向奎, 胡平, 等. 高强钢板22MnB5热成形的一步逆成形有限元方法［J］. 机械设计与制造, 2017(9): 13-15. LI Xiaoda, ZHANG Xiangkui, HU Ping, et al. One-step inverse forming FEM for hot forming of high-strength steel sheet［J］. Machinery Design & Manufacture, 2017(9): 13-15. ［7］SHIRIN M B, ASSEMPOUR A. Some improvements on the unfolding inverse finite element method for simulation of deep drawing process［J］. The International Journal of Advanced Manufacturing Technology, 2014, 72(1/2/3/4): 447-456. ［8］FARAHANI M K, SHIRIN M B, ASSEMPOUR A. Development of an inverse finite element method with an initial guess of linear unfolding［J］. Finite Elements in Analysis and Design, 2014, 79: 1-8. ［9］LIU Q S, XI J T, WU Z Q. An initial solution estimation method based on as-rigid-as-possible mesh parameterization for one-step simulation［J］. Engineering Computations, 2013, 30(3): 379-398. ［10］LIU Q S, XI J T, WU Z Q. An energy-based surface flattening method for flat pattern development of sheet metal components［J］. The International Journal of Advanced Manufacturing Technology, 2013, 68(5/6/7/8): 1155-1166. ［11］NA J X, WANG T, XU Z W, et al. Improvement research on the one-step algorithm for bus rollover collision based on the improved gradient method［J］. International Journal of Crashworthiness, 2015, 20(3): 270-279. ［12］周军, 马闯, 李光耀, 等. 基于有限元网格映射方法的精确反算求解毛坯［J］. 机械工程学报, 2002, 38(12): 103-106. ZHOU Jun, MA Chuang, LI Guangyao, et al. Exact optimum blank design using the wire mapping method based on the FEM resutls［J］. Chinese Journal of Mechanical Engineering, 2002, 38(12): 103-106.

[1]	张骥超1, 刘罡2, 林忠钦1, 高伟3, 李淑慧1. 侧围外板冲压工艺稳健性优化设计[J]. 上海交通大学学报（自然版）, 2012, 46(07): 1005-1010.
[2]	李将川1，陈军1，陈劼实1，夏志永2，曾丹2. 考虑预应变与烘烤时效的流动应力模型[J]. 上海交通大学学报（自然版）, 2013, 47(11): 1680-1684.
[3]	周杰1,戴洪1,陈勇锋1,陆俊江2,姚小兵2. 拉深翻边复合成形工艺参数多目标优化设计[J]. 上海交通大学学报（自然版）, 2014, 48(03): 412-416.
[4]	陈伟业a，邹天下a，唐鼎a，郭飞鹏a，李大永a, b. 铝箔板材成形极限试验及数值模拟[J]. 上海交通大学学报（自然版）, 2018, 52(9): 1081-1085.

基于逆有限元法和网格映射的板材成型坯料优化

Blank Optimization for Sheet Metal Forming Using Inverse Finite Element Method and Mesh Mapping

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 4

编辑推荐

Metrics

本文评价