考虑微凸体弹塑性过渡变形机制的结合面法向接触刚度分形模型

摘要/Abstract

摘要：

摘要：基于粗糙表面微凸体变形的连续性和光滑性原理，研究了在法向载荷逐渐增加时的粗糙表面单个微凸体弹塑性过渡变形机制，提出了考虑弹塑性过渡变形机制的结合面微凸体微观接触模型，建立了法向接触载荷和法向接触刚度的数学模型;基于分形几何理论，建立了结合面法向接触刚度的分形模型，并对结合面法向接触刚度进行仿真计算.结果表明：在较小的塑性指数条件下，法向接触载荷与法向接触刚度近似呈线性关系；在较大的塑性指数条件下，法向接触载荷与法向接触刚度呈非线性关系；法向接触刚度随着分形维数和法向接触载荷的增加而增大，随着无量纲分形特征尺度系数的增大而减小；所得结合面法向接触刚度的仿真计算值与铣削加工和磨削加工条件下的实验值较吻合.

关键词: 机械结合面, 法向接触刚度, 弹塑性接触, 分形模型, 微凸体

Abstract:

Abstract： Based on the contact mechanics theory, the deformation behavior of a single contacting asperity was studied, a micro contact model was proposed considering elastic-plastic transition deformation mechanism of rough surface joints, and a mathematical model of normal contact load and contact stiffness were established. Besides, the fractal model of mechanical joints normal contact load and contact stiffness were presented based on the fractal geometry theory. The results show that the plasticity index is lesser, the relationship between normal contact load and contact stiffness is approximately linear, and with the plastic index increasing, the relationship between normal contact load and contact stiffness is strongly nonlinear. The normal contact stiffness increases with increasing fractal dimension and normal contact load and decreases with increasing dimensionless fractal scale parameters. Moreover, the joints normal contact stiffness whose machining surface were milled and ground were calculated respectively by using the present model. The comparion of test results show that the present model is consistent with the experiment result.

Key words: machine joints, normal contact stiffness, elasticplastic contact, fractal model, asperity

中图分类号:

TH 113

何联格，左正兴，向建华. 考虑微凸体弹塑性过渡变形机制的结合面法向接触刚度分形模型[J]. 上海交通大学学报（自然版）, 2015, 49(01): 116-121.

HE Liange，ZUO Zhengxing，XIANG Jianhua. Normal Contact Stiffness Fractal Model Considering Asperity Elastic-Plastic Transitional Deformation Mechanism of Joints[J]. Journal of Shanghai Jiaotong University, 2015, 49(01): 116-121.

参考文献

［1］Fu W P，Huang Y M，Zhang X L．Experimental investigation of dynamic normal characteristics of machined joint surfaces［J］．ASME Journal of Vibration and Acoustics，2000，122(4): 393398．

［2］Ahmadian H，Jalali H．Identification of bolted lap joints parameters in assembled structures［J］．Mechanical Systems and Signal Processing，2007，21(2): 10411050．

［3］Shiryayev O V，Page S M，Pettit C L，et al．Parameter estimation and investigation of a bolted joint model［J］．Journal of Sound and Vibration，2007，307(35): 680697．

［4］Greenwood J A，Williamson J B P．Contact of nominally flat surfaces［C］∥ Proceedings of the Royal Society of London Series A, Mathematical and Physical Sciences. London: The Royal Society,1966，295: 300319．

［5］Chang W R, Etsion I, Bogy D B. An elasticplasticmodel for the contact of rough surfaces［J］. ASME Journal of Tribology，1987, 109(2): 257263．

［6］HandzelPowierza Z, Klimczak T, Polijaniuk A．On the experimental verification of the GreenwoodWilliamson model for the contact of rough surfaces［J］．Wear，1992，154（1）：115124．

［7］Zhao Y W，David D M，Chang L．An asperity microcontact model incorporating the transition from elastic deformation to fully plastic flow［J］．ASME Journal of Tribology，2000，122（1）：8693．

［8］Kogut L，Etsion I．Elasticplastic contact analysis of a sphere and rigid flat［J］．Journal of Applied Mechanics，2002，69：657662．

［9］赵永武，吕彦明，蒋建忠．新的粗糙表面弹塑性接触模型［J］．机械工程学报，2007，43(3)：95101．

ZHAO Yongwu，L Yanming，JIANG Jianzhong．New elasticplastic model for the contact of rough surfaces［J］．Chinese Journal of Mechanical Engineering，2007，43(3)：95101．

［10］Jiang S Y，Zheng Y J，Zhu H．A contact stiffness model of machined plane joint based on fractal theory［J］．Journal of Tribology，2010，132（1）：140117．

［11］杨红平，傅卫平，王雯，等．基于分形几何与接触力学理论的结合面法向接触刚度计算模型［J］．机械工程学报，2013，49(1)：102107．

YANG Hongping，FU Weiping，WANG Wen，et al．Calculation model of the normal contact stiffness of joints based on the fractal geometry and contact theory［J］．Chinese Journal of Mechanical Engineering，2013，49(1)：102107．

［12］张学良，黄玉美，傅卫平.粗糙表面法向接触刚度的分形模型［J］.应用力学学报，2000，17(2)：3135.

ZHANG Xueliang，HUANG Yumei，FU Weiping. Fractal model of normal contact stiffness between rough surfaces［J］.Chinese Journal of Applied Mechanics，2000，17(2)：3135．

［13］温淑花，张学良，武美先，等.结合面法向接触刚度分形模型与仿真［J］.农业机械学报，2009，40(11)：197202.

WEN Shuhua，ZHANG Xueliang，WU Meixian，et al. Fractal model and simulation of normal contact stiffness of joint interfaces and its simulation［J］.Transactions of the Chinese Society for Agricultural Machinery，2009，40(11)：197202．

［14］Shi X，Polycarpou A A．Investigation of contact stiffness and contact damping for magnetic storage headdisk interfaces［J］．ASME Journal of Tribology，2008，130(2): 02190119．

[1]	陈瑜1，2,滕克难1,唐金国1,王丽英1. 二维海面红外图像分形维数最优估计[J]. 上海交通大学学报（自然版）, 2018, 52(8): 1003-.
[2]	陈虹旭，董冠华，谢罗峰，殷鸣，殷国富. 分形粗糙表面接触变形分段计算模型[J]. 上海交通大学学报（自然版）, 2018, 52(6): 722-728.
[3]	唐睿1,2，胡成亮1，赵震1. 一种考虑侧接触切向滑动的微凸体弹塑性变形传热模型[J]. 上海交通大学学报（自然版）, 2017, 51(5): 520-.
[4]	尤晋闽, 陈天宁. 基于分形接触理论的结合面法向接触参数预估[J]. 上海交通大学学报（自然版）, 2011, 45(09): 1275-1280.