金属板料剪切试验方法及应用的研究现状

上海交通大学学报（自然版） ›› 2014, Vol. 48 ›› Issue (03): 422-426.

金属板料剪切试验方法及应用的研究现状

郑钰，李宏烨，庄新村，赵震

（上海交通大学塑性成形技术与装备研究院，上海 200030）

收稿日期:2013-07-24
基金资助:
国家自然科学基金资助项目（51105250）

A Review of Sheet Metal Shear Test Methods and Applications

ZHENG Yu,LI Hongye,ZHUANG Xincun,ZHAO Zhen

(Institute of Forming Technology and Equipment, Shanghai Jiaotong University, Shanghai 200030, China)

Received:2013-07-24

摘要/Abstract

摘要：

阐述了板料剪切试验的研究现状，按照板料夹持方式将其分为螺栓多点夹持、夹头集中夹持和板面压紧夹持；介绍了各夹持方式的典型装置和试样，根据夹持力的施加方式分析了受力状态，按照与纯剪受力状态的近似程度进行评定，得出了3种方式的优劣评价.

关键词: 板料剪切试验, 力学性能测试, 夹持方式, 各向异性

Abstract:

Domestic and international research on sheet metal shear tests was reviewed in this paper, in which the tests were divided into three types, that is, multipoint bolt clamping, linear concentrated clamping, and surface uniform clamping, in accordance with the sheet clamping method. The typical devices and samples of each clamping method were introduced. According to the way of clamping force applied, the stress states were analyzed.
Based on the approximation to the simple shear stress state, judgments from different characteristics of the three methods were acquired.

Key words: sheet metal shear test, mechanical property testing, clamping methods, anisotropy

中图分类号:

TG 707

郑钰，李宏烨，庄新村，赵震. 金属板料剪切试验方法及应用的研究现状[J]. 上海交通大学学报（自然版）, 2014, 48(03): 422-426.

ZHENG Yu,LI Hongye,ZHUANG Xincun,ZHAO Zhen. A Review of Sheet Metal Shear Test Methods and Applications[J]. Journal of Shanghai Jiaotong University, 2014, 48(03): 422-426.

参考文献

［1］Carbonniere J, Thuillier S, Sabourin F, et al. Comparison of the work hardening of metallic sheets in bending–unbending and simple shear［J］. International Journal of Mechanical Sciences, 2009, 51:122130.

［2］王进, 陈军, 张斌, 等. 35CrMo结构钢热塑性变形流动应力模型［J］.上海交通大学学报, 2005, 39(11):17841791.

WANG Jin, CHEN Jun, ZHANG Bin, et al. The flow stress model of 35CrMo structural steel during hot forming［J］. Journal of Shanghai Jiaotong University, 2005, 39(11):17841791.

［3］Rusinek A, Klepaczko J R. Shear testing of a sheet steel at wide range of strain rates and a constitutive relation with strainrate and temperature dependence of the flow stress［J］. International Journal of Plasticity, 2001, 17:87115.

［4］Bouvier S, Gardey B, Haddady H, et al. Characterization of the straininduced plastic anisotropy of rolled sheets by using sequences of simple shear and uniaxial tensile tests［J］. Journal of Materials Processing Technology, 2006, 174:115126.

［5］Thuillier S, Manach P Y. Comparison of the workhardening of metallic sheets using tensile and shear strain paths［J］. International Journal of Plasticity, 2009, 25:733 751.

［6］Rauch E F. Plastic anisotropy of sheet metals determined by simple shear tests［J］. Materials Science and Engineering A, 1998, 241:179 183.

［7］Gasperini M, Pinna C, Swiatnicki S. Microstructure evolution and strain localization during shear deformation of an alluminum alloy［J］. Acta Material, 1996, 44(10):4195 4208.

［8］Peir J, Verleyson P, Van Paepegem W, et al. Determining the stressstrain behavior at large strains from high strain rate ensile and shear experiments［J］. International Journal of Impact Engineering, 2011, 38:406 415.

［9］Yin Q, Soyarslan C, Guner A, et al. A cyclic twin bridge shear test for the identification of kinematic hardening parameter［J］. International Journal of Mechanical Sciences, 2012, 59:31 43.

［10］孔庆瑞, 王家莲. 方形截面试样单剪切试验装置的设计［J］. 工程与试验, 2010(增刊):3940.

KONG Qinrui, WANG Jialian. Design on single shear test for square section specimen［J］. Engineering and Test, 2010(Sup.):3940.

［11］黄小明, 胡世光. 纯剪试验研究［J］. 锻压技术, 1991(5):2124.

HUANG Xiaoming, HU Shiguang. Research of simple shearing test［J］. Forging and Stamping Technology, 1991(5):2124.

[1]	荣富, 廖晨聪, 童大贵, 周香莲. 波浪作用下渗透率各向异性的海床液化分析[J]. 上海交通大学学报, 2019, 53(1): 93-99.
[2]	徐长节1,2,3，梁禄钜1，丁文湘4. 深埋圆形隧洞围岩各向异性稳态渗流场解析解[J]. 上海交通大学学报（自然版）, 2018, 52(12): 1565-1570.
[3]	史冬岩，王青山，石先杰，庄重. 任意边界条件下正交各向异性薄板自由振动特性分析[J]. 上海交通大学学报（自然版）, 2014, 48(03): 434-438.
[4]	李科1，2，王颖轶3，黄醒春3. 一种裂隙岩体力学参数的评价方法及应用[J]. 上海交通大学学报（自然版）, 2013, 47(10): 1569-1573.
[5]	卢健，陈军，张飞飞，陈劼实. 基于三维Hill’48屈服准则的液压成形本构模型及数值验证[J]. 上海交通大学学报（自然版）, 2013, 47(05): 791-794.
[6]	孔艳平a, 陈长虹b, 刘金喜a. 正交各向异性弹性层/功能梯度压电半空间结构中Love波的传播[J]. 上海交通大学学报（自然版）, 2013, 47(02): 210-215.
[7]	肖骥1，Etienne Pessard2，王敏1，Daniel Cuillerier2. 7475铝合金板材的各向异性疲劳性能[J]. 上海交通大学学报（自然版）, 2011, 45(11): 1678-1683.
[8]	牛建辉，朱平,郭永进. 热镀锌双相钢DP590力学特性及其本构模型 [J]. 上海交通大学学报（自然版）, 2010, 44(10): 1382-1387.