浸液式高速往复走丝电火花线切割漏电损失

上海交通大学学报（自然版） ›› 2013, Vol. 47 ›› Issue (11): 1670-1674.

浸液式高速往复走丝电火花线切割漏电损失

张伟建，刘志东，邱明波

(南京航空航天大学机电学院，南京 210016)

收稿日期:2012-12-09
基金资助:
国家自然科学基金(50975142)，江苏省工业支撑计划(BE2009161)资助项目

Leakage Current Loss in Immersion Fluid High Speed Wire-Cut Electrical Discharge Machining

ZHANG Weijian，LIU Zhidong，QIU Mingbo

（College of Mechanical and Electrical Engineering， Nanjing University of Aeronautics and Astronautics， Nanjing 210016， China）

Received:2012-12-09

摘要/Abstract

摘要：

分析了放电能量损失与极间工作液漏电、工件表面漏电的关系.采用浸液和喷液2种冷却方式进行高速往复走丝电火花线切割加工实验，对理论分论结果进行了验证.结果表明：减小工件表面漏电面积和工作液电导率，可以有效减少能量损失，进而提高加工效率；在相同加工参数下,浸液式相对于喷液式切割速度有所降低，其主要原因是由浸没在工作液中的工件与电极丝间持续电解漏电形成的.

关键词: 电火花线切割, 喷液加工, 浸液加工, 漏电损失

Abstract:

Both immersion fluid and spray liquid cooling methods were used in high speed wire-cut electrical discharge machining(HSWEDM) experiments. The results show that with the same processing parameters, the cutting speed of immersion fluid is lower than that of spray liquid. A primary cause of this is the continuous leakage current of electrolytic between the work-piece and wire electrode which covered with electrolyte liquid. The relationship of the discharge energy loss and the leakage current between electrolyte liquid and the leakage current of work-piece were analyzed. The experimental results show that by reducing the surface leakage current area of the work-piece and working fluid conductivity, the energy loss could be effectively reduced, and the processing efficiency could be improved.

Key words: WEDM(wire-cut electrical discharge machining), spray liquid processing, immersion fluid processing, leakage current loss

中图分类号:

TG 662

张伟建，刘志东，邱明波. 浸液式高速往复走丝电火花线切割漏电损失[J]. 上海交通大学学报（自然版）, 2013, 47(11): 1670-1674.

ZHANG Weijian，LIU Zhidong，QIU Mingbo. Leakage Current Loss in Immersion Fluid High Speed Wire-Cut Electrical Discharge Machining[J]. Journal of Shanghai Jiaotong University, 2013, 47(11): 1670-1674.

参考文献

［1］王振兴. 高低双速走丝电火花线切割工艺研究［D］.南京：南京航天航空大学机电学院, 2010.

［2］刘志东, 俞容亨. 高速走丝电火花线切割机床多次切割的实现［J］.中国机械工程,2007,18（20）:24102413.

LIU Zhidong, YU Rongheng. Realization of multicutting in WEDMHS［J］. Chinese Journal of Mechanical Engineering, 2007,18(20): 24102413.

［3］Cheng G, Han F Z, Feng Z J. Experimental determination of convective heat transfer coefficient in WEDM［J］. International Journal of Machine Tools & Manufacture,2007, 47: 17441751.

［4］潘湛昌, 郭钟宁, 王成勇.高速走丝电火花线切割中工作液的电解作用［J］.电加工,1996, 2:1719.

PAN Shenchang, GUO Zhongning, WANG Chengyong. Influence of the work fluid electrolysis in HSWEDM［J］. Electromachining & Mould,1996,2:1719.

［5］韩强, 狄士春, 赵万生.慢走丝线切割电解锈蚀放电状态的分析和控制［J］.航空精密制造技术,1995,35(2):1012.

HAN Qiang, DI Shichun, ZHAO Wansheng. Electrolytic corrosion discharge state analysis and control in LSWEDM［J］. Aviation Precision Manufacturing Technology, 1995, 35(2):1012.

［6］刘志东, 魏为, 陆霖琰,等.电火花线切割极间介电特性与放电能量分配关系［J］.上海交通大学学报，2012,46（7）：10151020.

LIU Zhidong, WEI Wei, LU Linyan, et al. Research of relationship between interelectrode dielectric properties and energy distribution in wire electrical discharge machining［J］. Journal of Shanghai Jiaotong University,2012,46(7):10151020.

［7］朱宁, 许庆平, 朱伟根,等.低速走丝电火花线切割加工工艺研究［J］.电加工与模具,2008,3:5963.

ZHU Ning, XU Qingping, ZHU Weigen, et al. Process study of LSWEDM［J］. Electromachining & Mould, 2008, 3: 5963.