7075-T6高强度铝合金温热条件下的拉深成形性能

上海交通大学学报（自然版） ›› 2012, Vol. 46 ›› Issue (09): 1482-1486.

7075-T6高强度铝合金温热条件下的拉深成形性能

周国伟a，李大永a,b，彭颖红a,b

(上海交通大学a.机械与动力工程学院； b.机械系统与振动国家重点实验室, 上海 200240)

收稿日期:2012-02-28 出版日期:2012-09-28 发布日期:2012-09-28
基金资助:
上海市科学技术委员会资助项目（10QH1401400）

Deep Drawability of 7075-T6 High Strength Aluminum Alloy at Warm Condition

ZHOU Guo-Wei-a, LI Da-Yong-a, b , PENG Ying-Hong-a, b

(a.School of Mechanical Engineering; b. State Key Laboratory of Mechanical System and Vibration, Shanghai Jiaotong University, Shanghai 200240, China)

Received:2012-02-28 Online:2012-09-28 Published:2012-09-28

摘要/Abstract

摘要： 采用温热拉深试验方法研究了在50~250 °C范围内，温度、压边力和成形速度对高强度铝合金7075-T6成形性能的影响.结果表明：在等温条件下，7075T6的极限拉深比随着温度升高而先增后减；在差温条件下，极限拉深比随着温度升高而增大，当温度超过150 °C时，其极限拉深比较等温条件的大；随着温度升高，拉深成形所需要的力降低；在等温或差温条件下，虽其极限拉深比的差别较大，但其杯形件厚度的变化规律基本一致；当压边力为5 kN，速度为10 mm/min时，试样的成形性能最佳.

关键词: 高强度铝合金, 温热成形, 极限拉深比

Abstract: The forming properties of 7075-T6 high strength aluminum alloy were studied in the temperature range of 50~250 °C by warm deep drawing test. The experimental results show that: the limit drawing ratio(LDR) first shows an increasing trend and then decreases at the same tools temperature condition; while at different tools temperatures condition the LDR increases with temperature gradually, the drawability at different tools temperatures condition exceeds that of same tools temperature condition when the temperature is over 150 °C, the maximum load force declines with temperature increasing. The LDRs at various temperatures are different while the thickness of cross-section does not change apparently. The influences of holder force and punch velocity were investigated: the material could have better forming properties when the holder force is 5 kN, punch speed 10 mm/min.

Key words: high strength aluminum alloy, warm form, limiting drawing ratio

中图分类号:

TG 386

周国伟a, 李大永a, b, 彭颖红a, b. 7075-T6高强度铝合金温热条件下的拉深成形性能[J]. 上海交通大学学报（自然版）, 2012, 46(09): 1482-1486.

ZHOU Guo-Wei-a, LI Da-Yong-a, b , PENG Ying-Hong-a, b . Deep Drawability of 7075-T6 High Strength Aluminum Alloy at Warm Condition[J]. Journal of Shanghai Jiaotong University, 2012, 46(09): 1482-1486.

参考文献

［1］石其年, 熊惟皓. 铝合金在汽车中的应用与发展［J］. 新技术新工艺, 2006(12): 5558.

SHI Qinian, XIONG Weihao. Application and development of aluminum alloys in automobile industry ［J］. New Technology and New Process, 2006(12): 5558.
［2］Miller W S, Zhuang L, Bottema J, et al. Recent development in aluminum alloys for the automotive industry ［J］. Materials Science and Engineering A, 2000, 280(1): 3749.
［3］王孟君，周威，任杰, 等. 汽车用5182铝合金的温拉深成形性能［J］. 中南大学学报:自然科学版, 2010, 41 (3): 936939.
WANG Mengjun, ZHOU Wei, REN Jie, et al. Forming properties of 5182 aluminum alloy for automotive body sheet during warm deep drawing processes ［J］. Journal of Central South University: Science and Technolog, 2010, 41 (3): 936939.
［4］Abedrabbo N, Pourboghrat F, Carsley J. Forming of AA5182O and AA5754O at elevated temperatures using coupled thermomechanical finite element models ［J］. International Journal of Plasticity, 2007, 23 (5): 841875.
［5］黄华, 李大永, 彭颖红. 7075T6 铝合金板温热成形极限图实验［J］. 塑性工程学报, 2010, 17 (1): 9397.
HUANG Hua, LI Dayong, PENG Yinghong. Experimental study on the forming limit diagrams (FLD) of 7075T6 aluminum alloy sheet at warm state ［J］. Journal of Plasticity Engineering, 2010, 17 (1): 9397.
［6］Naka T, Yoshida F. Deep drawability of type 5083 aluminummagnesium alloy under various conditions of temperature and forming speed ［J］. Journal of Material Processing Technology, 1999, 8990: 1923.
［7］Moon Y H, Kang Y K, Park J W, et al. Tool temperature control to increase the deep drawability of aluminum 1050 sheet ［J］. International Journal of Machine Tools and Manufacture, 2001, 41 (9): 12831294.
［8］Robinson J M, Shaw M P. Microstructural and mechanical influences on dynamic strain aging phenomena ［J］. International Material Reviews, 1994, 39 (3): 113122.