在FTM200型摩擦磨损试验机上，以PH13-8Mo不锈钢为配副件，采用正交试验方法在低温-45，-20 ℃以及室温条件下探讨了法向载荷、微动频率和微动振幅及试验时间对碳纤维增强环氧树脂基复合材料微动摩擦磨损性能的影响.结果表明，法向载荷、微动频率和振幅、试验时间以及温度对摩擦系数的影响均非常显著.在-45 ℃时，复合材料的摩擦系数均高于室温时的摩擦系数.法向载荷和温度对复合材料磨损量的影响显著.在相同的温度下，复合材料磨损量随法向载荷的增大而增加；在相同的法向载荷下，-45 ℃时，复合材料的磨损量较室温时的大，其磨损区域萌生出较多的微动裂纹，疲劳剥落现象较明显，其微动磨损机制以疲劳磨损为主；而在室温下，其磨损表面主要为表面树脂的刮痕以及少量的微动裂纹，其微动磨损机制为磨粒磨损.
The FTM200 friction and wear tester was used and the PH13-8Mo stainless steel was taken as the friction couple and an orthogonal experiment was applied to studying the influences of normal load, fretting frequency, fretting amplitude and test time on the tribological property of carbon fiber reinforced epoxy resin matrix composites at -45 ℃, -20 ℃ and room temperature. The results showed that normal load, fretting frequency, fretting amplitude, test time and temperature affected the friction coefficient very significantly. Friction coefficients of the samples at -45 ℃ were higher than that at room temperature, for the matrix was friable under low temperature and the components were peeled off more easily in the wear process, resulting in increase of wear rate. The influence of normal load and temperature on the wear of composite was more obvious. Under the same temperature, the wear volume of composite increased with the increase of the load. Under the same load, the wear volume of composite at -45 ℃ was larger than that at room temperature, indicating that the fretting and the spalling fatigue occurred more easily. At room temperature, the surface scratching of the composite and some cracks were mainly characterized. The fretting wear mechanism of the carbon fiber reinforced epoxy resin-based composites was abrasive wear and fatigue wear, while the wear mechanism of the material at low temperature mainly focused on fatigue wear.
［1］黄洋, 袁春野, 宋世涛. 碳纤维复合材料在航天领域的应用［J］. 科技展望, 2017, 27(26): 175.
HUANG Yang, YUAN Chunye, SONG Shitao. Application of carbon fiber composites to cosmonautic fields［J］. Science and Technology, 2017, 27(26): 175.
［2］姜茂川, 范雨娇. 国内碳纤维产业发展浅析及展望［J］. 新材料产业, 2017 (8): 38-43.
JIANG Maochuan, FAN Yujiao. Analysis and prospect of domestic carbon fiber industry development［J］. Advanced Materials Industry, 2017(8): 38-43.
［3］林修洲, 朱旻昊, 郑健峰, 等. TC4钛合金微弧氧化涂层的制备与微动磨损性能研究［J］. 中国有色金属学报, 2010, 20(4): 537-546.
LIN Xiuzhou, ZHU Minhao, ZHENG Jianfeng, et al. Fretting wear of micro-arc oxidation coating prepared on Ti6Al4V alloy［J］. Transactions of Nonferrous Metals Society of China, 2010, 20(4): 537-546.
［4］高喜军, 尚文博, 高知辉, 等. 碳纤维增强摩擦材料的设计与研究［J］. 材料导报, 2015, 29(2): 82-86.
GAO Xijun, SHANG Wenbo, GAO Zhihui, et al. Design and research of carbon fiber reinforced friction materials［J］. Materials Review, 2015, 29(2): 82-86.
［5］ZHANG R L, GAO B, DU W T, et al. Enhanced mechanical properties of multiscale carbon fiber/epoxy composites by fiber surface treatment with graphene oxide/polyhedral oligomeric silsesquioxane［J］. Composites Part A: Applied Science and Manufacturing, 2016, 84: 455-463.
［6］殷艳飞, 刘莹, 丁郭, 等. 碳纤维增强树脂基摩擦材料摩擦磨损性能［J］. 宇航材料工艺, 2016, 46(2): 31-35.
YIN Yanfei, LIU Ying, DING Guo, et al. Friction and wear properties of carbon fiber reinforced resin-based friction material［J］. Aerospace Materials and Technology, 2016, 46(2): 31-35.
［7］刘新, 武湛君, 何辉永, 等.单向碳纤维复合材料的超低温力学性能［J］. 复合材料学报, 2017, 34(11): 2437-2445.
LIU Xin, WU Zhanjun, HE Huiyong, et al. Cryogenic mechanical properties of unidirectional carbon fibers reinforced plastics［J］. Acta Materiae Compositae Sinica, 2017, 34(11): 2437-2445.
［8］翁春晓. 超低温用环氧树脂及其碳纤维织物增强复合材料的研究［D］. 武汉: 武汉理工大学材料科学与工程学院, 2012.
WENG Chunxiao. Research on cryogenic epoxy resin and carbon fiber fabric enhanced composite materials［D］. Wuhan: College of Material Science and Engineering, Wuhan University of Technology, 2012.
［9］DHIEB H, BUIJNSTERS J G, EDDOUMY F, et al. Surface and sub-surface degradation of unidirectional carbon fiber reinforced epoxy composites under dry and wet reciprocating sliding［J］. Composites Part A: Applied Science and Manufacturing, 2013, 55: 53-62.
［10］徐小军, 刘捍卫, 朱旻昊, 等. Ti-Al-Zr钛合金的高温微动磨损行为研究［J］. 核动力工程, 2010, 31(5): 42-47.
XU Xiaojun, LIU Hanwei, ZHU Minhao, et al. Study on high temperature fretting wear of Ti-Al-Zr alloy［J］. Nuclear Power Engineering, 2010, 31(5): 42-47.
