针对活塞环-缸套系统的摩擦行为建立了模型并进行数值求解，考虑了气穴现象和混合润滑的影响，研究了低黏度润滑油条件下织构对活塞环-缸套系统摩擦特性的影响，对比了在低黏度润滑油SAE0W20和SAE5W20的条件下活塞环表面含半径30μm、深度3μm的球形织构与不含织构的活塞环-缸套系统摩擦特性.结果表明：织构的作用与润滑油黏度密切相关；在润滑油SAE0W20的条件下，球形织构起到了一定的减摩作用；在润滑油SAE5W20的条件下，球形织构增大了系统的摩擦功率损失和摩擦平均有效压力.
The paper built a numerical model for analyzing friction of piston ring-liner system, which considered the influence of cavitation and mixed lubrication. To investigate the synergistic effect of low viscosity and surface texture, two types of low viscosity oils, i.e. SAE0W20 and SAE5W20, were selected. Besides, the friction of piston ring with spherical texture, which was with a radius of 30μm and a depth of 3μm, was compared to the friction of piston ring without surface texture. The results show that the impact of surface texture is closely related to the viscosity of lubricating oil. Under condition of lubricating oil SAE0W20, the spherical texture helps to reduce friction, while under condition of lubricating oil SAE 5W20, the spherical texture increases friction power loss and friction mean effective pressure.
［1］严新平, 袁成清, 白秀琴, 等.船舶摩擦学的发展展望［J］.自然杂志, 2015, 37(3): 157-164.
YAN Xinping, YUAN Chengqing, BAI Xiuqin, et al. Review and prospect of marine tribology［J］. Chinese Journal of Nature, 2015, 37(3): 157-164.
［2］邵林波.汽车发动机润滑油的选用分析［J］.昆明冶金高等专科学校学报, 2014, 30(1): 66-69.
SHAO Linbo. Analysis of selection of automobile engine oil［J］. Journal of Kunming Metallurgy College, 2014, 30(1): 66-69.
［3］LENAUER C, TOMASTIK C, WOPELKA T, et al. Piston ring wear and cylinder liner tribofilm in tribotests with lubricants artificially altered with ethanol combustion products［J］. Tribology International, 2015, 82: 415-422.
［4］李凯凯, 于海武, 王静秋, 等.混合织构发动机缸套的减摩试验研究［J］. 内燃机工程, 2014, 35(5): 113-118.
LI Kaikai, YU Haiwu, WANG Jingqiu, et al. Experimental investigation on friction reduction of mixed texture cylinder liner［J］. Chinese Internal Combustion Engine Engineering, 2014, 35(5): 113-118.
［5］MACIN V, TORMOS B, RUIZ S, et al.Low viscosity engine oils: Study of wear effects and oil key parameters in a heavy duty engine fleet test［J］. Tribology International, 2016, 94: 240-248.
［6］TORMOS B, RAMREZ L, JOHANSSON J, et al. Fuel consumption and friction benefits of low viscosity engine oils for heavy duty applications［J］. Tribology International, 2017, 110: 23-34.
［7］张慧慧. 面接触下表面形貌对动压润滑性能影响的研究［D］.青岛：青岛理工大学机械工程学院, 2013.
ZHANG Huihui. Study on the surface morphology effects on the hydrodynamic lubrication in conformal contact ［D］. Qingdao: School of Mechanical Engineering, Qingdao Technological University, 2013.
［8］李媛, 刘小君, 张彦, 等. 面接触条件下织构表面摩擦特性研究［J］. 机械工程学报, 2012, 48(19): 109-115.
LI Yuan, LIU Xiaojun, ZHANG Yan, et al. Frictional properties of textured surfaces under plane contact［J］. Journal of Mechanical Engineering, 2012, 48(19): 109-115.
［9］GRABON W, PAWLUS P, WOS S, et al. Effects of honed cylinder liner surface texture on tribological properties of piston ring-liner assembly in short time tests［J］. Tribology International, 2017, 113: 137-148.
［10］USMAN A, PARK C W. Optimizing the tribological performance of textured piston ring-liner contact for reduced frictional losses in SI engine: Warm operating conditions［J］. Tribology International, 2016, 99: 224-236.
［11］BIBOULET N, LUBRECHT A A. Analytical solution for textured piston ring—Cylinder liner contacts (1D analysis)［J］. Tribology International, 2016, 96: 269-278.
［12］OBERT P, MLLER T, FBER H J, et al. The influence of oil supply and cylinder liner temperature on friction, wear and scuffing behavior of piston ring cylinder liner contacts—A new model test［J］. Tribology International, 2016, 94: 306-314.
［13］乔姣飞, 常秋英. 表面织构对二硫化钼喷涂膜摩擦学性能的影响［J］. 润滑与密封, 2016, 41(1): 55-58.
QIAO Jiaofei, CHANG Qiuying. Influence of surface texture on the tribological properties of molybdenum disulfide spraying film［J］. Lubrication Engineering, 2016, 41(1): 55-58.
［14］QIU Y, Khonsari M M. Performance analysis of full-film textured surfaces with consideration of roughness effects［J］. Journal of Tribology, 2011, 133(2): 021704-1-10.
［15］PATIR N, CHENG H S. An average flow model for determining effects of three-dimensional roughness on partial hydrodynamic lubrication［J］. Journal of Tribology, 1978, 100(1): 12-17.
［16］WOLOSZYNSKI T, PODSIADLO P, STACHOWIAK G W. Efficient solution to the cavitation problem in hydrodynamic lubrication［J］. Tribology Letters, 2015, 58(1): 18-1-11.
［17］GU C X, MENG X H, XIE Y B, et al. Mixed lubrication problems in the presence of textures: An efficient solution to the cavitation problem with consideration of roughness effects［J］. Tribology International, 2016, 103: 516-528.
［18］GREENWOOD J A, TRIPP J H. The contact of two nominally flat rough surfaces［J］. Proceedings of the Institution of Mechanical Engineers, 1970, 185(1): 625-633.
［19］王素华, 吴新跃. 基于表面织构的机械部件摩擦学性能改善研究进展［J］. 机床与液压, 2012, 40(11): 142-145.
WANG Suhua, WU Xinyue. Research on improving tribological performance of mechanical components by surface texture［J］. Machine Tool and Hydraulics, 2012, 40(11): 142-145.
