模具温升对22MnB5硼钢裸板高温摩擦磨损特性的影响

doi:10.16183/j.cnki.jsjtu.2019.226

上海交通大学学报 ›› 2021, Vol. 55 ›› Issue (3): 258-264.doi: 10.16183/j.cnki.jsjtu.2019.226

所属专题：《上海交通大学学报》2021年12期专题汇总专辑；《上海交通大学学报》2021年“金属学与金属工艺”专题

模具温升对22MnB5硼钢裸板高温摩擦磨损特性的影响

蒋怡涵, 吴佳松, 王武荣(), 韦习成

上海大学　材料科学与工程学院，上海　200072

收稿日期:2019-07-29 出版日期:2021-03-01 发布日期:2021-04-02
通讯作者: 王武荣 E-mail:wrwang@shu.edu.cn
作者简介:蒋怡涵(1994-)，女，江苏省徐州市人，硕士生，主要研究方向为板材热冲压成形．
基金资助:
国家自然科学基金(51475280)

Effect of Mold Heating on High-Temperature Friction and Wear Characteristics of Uncoated 22MnB5 Boron Steel

JIANG Yihan, WU Jiasong, WANG Wurong(), WEI Xicheng

School of Materials Science and Engineering, Shanghai University, Shanghai 200072, China

Received:2019-07-29 Online:2021-03-01 Published:2021-04-02
Contact: WANG Wurong E-mail:wrwang@shu.edu.cn

摘要/Abstract

摘要：

采用自制板带式高温摩擦磨损试验机模拟实际热冲压条件下22MnB5硼钢裸板的高温摩擦过程，对模具进行预热，模拟了热冲压过程中的模具升温，并通过硼钢热冲压的摩擦因数、表面磨损形貌和截面图及基体组织图研究模具升温对硼钢裸板摩擦行为及机理的影响．结果表明：模具升温较低时，硼钢裸板与H13钢之间的摩擦因数基本稳定在0.5，其磨损机理以磨粒磨损和黏着磨损为主．当模具升温超过100 ℃，硼钢裸板摩擦因数随温度升高呈现下降趋势，在150 ℃和200 ℃分别为0.474和0.414，黏着磨损作用减弱．硼钢基体维氏硬度在室温至100 ℃基本稳定在430，随温度进一步升至150 ℃和200 ℃，硬度分别降至413.5和399.7，表明模具升温对成型件机械性能有显著影响．

关键词: 热冲压, 22MnB5裸板, 高温摩擦磨损, 模具升温

Abstract:

A self-developed strip-type high-temperature friction and wear test device was used to simulate the high-temperature friction process of uncoated 22MnB5 boron steel under actual hot stamping conditions. The mold was preheated to simulate the temperature increase of the die in the hot stamping process. The effects of mold temperature on the friction behavior and mechanism of uncoated boron steel were studied by using the friction coefficient test, surface wear morphology observation, and cross-section and matrix structure chart of hot stamping boron steel. The results show that the friction coefficient between the uncoated boron steel and the H13 steel is basically stable at 0.5 when the temperature of the mold is low, and the wear mechanism is mainly classified to abrasive wear and adhesive wear. Besides, when the mold temperature exceeds 100 ℃,the friction coefficient of the uncoated boron steel decreases from 0.474 to 0.414 with an increase of temperature from 150 ℃ to 200 ℃,inferring that the adhesive wear is weakened. The Vickers hardness of the boron steel matrix is approximately close to 430 from room temperature to 100 ℃. Moreover, with the temperature further rising to 150 ℃ and 200 ℃,the hardness decreases to 413.5 and 399.7 respectively, which indicates that the mold temperature has a significant effect on the mechanical behavior of formed parts.

Key words: hot stamping, uncoated 22MnB5 steel, high-temperature friction and wear, mold heating

中图分类号:

TG115

蒋怡涵, 吴佳松, 王武荣, 韦习成. 模具温升对22MnB5硼钢裸板高温摩擦磨损特性的影响[J]. 上海交通大学学报, 2021, 55(3): 258-264.

JIANG Yihan, WU Jiasong, WANG Wurong, WEI Xicheng. Effect of Mold Heating on High-Temperature Friction and Wear Characteristics of Uncoated 22MnB5 Boron Steel[J]. Journal of Shanghai Jiao Tong University, 2021, 55(3): 258-264.

图/表 12

图1

表1

图2

图3

图4

表2

图5

图6

图7

图8

图9

图10

参考文献 14

[1]	陈辉，景财年. 热成形技术在汽车轻量化中的应用与发展[J]. 金属热处理，2016, 41(3): 61-66.
	CHEN Hui, JING Cainian. Application and development of hot forming technology for automobile lightening[J]. Heat Treatment of Metals, 2016, 41(3): 61-66.
[2]	CASTRO M R, MONTEIRO W A, POLITANO R. Enhancements on strength of body structure due to bake hardening effect on hot stamping steel[J]. The International Journal of Advanced Manufacturing Technology, 2019, 100(1): 771-782.
[3]	郑先坤，王武荣，韦习成. 热镀锌先进高强度钢板摩擦耦合塑性变形行为[J]. 上海交通大学学报，2017, 51(4): 432-437.
	ZHENG Xiankun, WANG Wurong, WEI Xicheng. Plastic deformation behavior of hot-dipped advanced galvanized steel under the condition of friction coupling[J]. Journal of Shanghai Jiao Tong University, 2017, 51(4): 432-437.
[4]	GRACIA-ESCOSA E, GARCÍA I, DAMBORENEA J J D, et al. Friction and wear behaviour of tool steels sliding against 22MnB5 steel[J]. Journal of Materials Research and Technology, 2017, 6(3): 241-250.
[5]	张磊，赵玉璋，王武荣，等. 超高强度硼钢B1500HS的热冲压工艺试验[J]. 上海交通大学学报，2015, 49(1): 12-18.
	ZHANG Lei, ZHAO Yuzhang, WANG Wurong, et al. Experimental study of hot stamping process of B1500HS ultra high born steel[J]. Journal of Shanghai Jiao Tong University, 2015, 49(1): 12-18.
[6]	SCHWINGENSCHLÖGL P, TENNER J, MERKLEIN M. Tribological behavior of different tool steels and surface properties under hot stamping conditions[J]. Key Engineering Materials, 2018, 767: 212-219.
[7]	TIAN X W, ZHANG Y S, LI J. Investigation on tribological behavior of advanced high strength steels: Influence of hot stamping process parameters[J]. Tribology Letters, 2012, 45(3): 489-495.
[8]	GHIOTTI A, BRUSCHI S, SGARABOTTO F, et al. Tribological performances of Zn-based coating in direct hot stamping[J]. Tribology International, 2014, 78: 142-151.
[9]	HARDELL J, HERNANDEZ S, MOZGOVOY S, et al. Effect of oxide layers and near surface transformations on friction and wear during tool steel and boron steel interaction at high temperatures[J]. Wear, 2015, 330/331: 223-229.
[10]	贺斌，邓泽涵，张万鑫，等. 热冲压模具冷却水道FEM-CFD耦合优化研究[J]. 热加工工艺，2014, 43(3): 1-4.
	HE Bin, DENG Zehan, ZHANG Wanxin, et al. Optimization of cooling channels for hot stamping die based on FEM-CFD coupled method[J]. Hot Working Technology, 2014, 43(3): 1-4.
[11]	王铖，李辉平，贺连芳，等. 加热温度和模具温度对 B1500HS硼钢组织与性能的影响[J]. 金属热处理，2016, 41(10): 43-48.
	WANG Cheng, LI Huiping, HE Lianfang, et al. Effects of heating temperature and mold temperature on microstructure and properties of B1500HS boron steel[J]. Heat Treatment of Metals, 2016, 41(10): 43-48.
[12]	LIU W, LIU H S, XING Z W, et al. Effect of tool temperature and punch speed on hot stamping of ultra high strength steel[J]. Transactions of Nonferrous Metals Society of China, 2012, 22: s534-s541.
[13]	刘建国，孙书林，王玉峰. 影响热冲压制件品质的主要因素[J]. 模具制造，2016, 16(10): 31-33.
	LIU Jianguo, SUN Shulin, WANG Yufeng. Main factors of affecting the quality for hot stamping parts[J]. Die & Mould Manufacture, 2016, 16(10): 31-33.
[14]	VENTURATO G, NOVELLA M, BRUSCHI S, et al. Effects of phase transformation in hot stamping of 22MnB5 high strength steel[J]. Procedia Engineering, 2017, 183: 316-321.

材料	w/%									硬度
材料	C	Si	Mn	Cr	P	S	Mo	B	V	硬度
22MnB5	0.258	0.250	1.240	0.143	0.021	0.005	0.005	0.003	0.006	维氏硬度180
H13	0.391	0.911	0.374	5.180	0.015	0.015	1.450	0.003	0.953	洛氏硬度53.1

模具温升对22MnB5硼钢裸板高温摩擦磨损特性的影响

Effect of Mold Heating on High-Temperature Friction and Wear Characteristics of Uncoated 22MnB5 Boron Steel

RichHTML

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

图/表 12

参考文献 14

相关文章 4

编辑推荐

Metrics

本文评价

[1]	高凯翔,王武荣,韦习成,孟华. 22MnB5硼钢裸板热成形中的高温摩擦[J]. 上海交通大学学报, 2019, 53(9): 1136-1142.
[2]	丁亚男，谭淑霖，韩先洪，崔振山. 硼钢热冲压产品的力学性能预测模型及U型件验证[J]. 上海交通大学学报, 2017, 51(11): 1320-1327.
[3]	唐炳涛, 李琛琛, 郑伟, 黄丽丽, 原政军. 高强钢激光拼焊板热冲压材料模型的构建及实验验证[J]. 上海交通大学学报, 2016, 50(7): 994-999.
[4]	张磊，赵玉璋，王武荣，韦习成. 超高强度硼钢B1500HS的热冲压工艺试验[J]. 上海交通大学学报（自然版）, 2015, 49(01): 12-18.