机械密封用O形橡胶密封圈微动特性

上海交通大学学报（自然版） ›› 2014, Vol. 48 ›› Issue (06): 856-862.

机械密封用O形橡胶密封圈微动特性

郑金鹏，沈明学，孟祥铠，厉淦，彭旭东

（浙江工业大学过程装备及其再制造教育部工程研究中心，杭州 310032）

收稿日期:2013-10-06
基金资助:
国家重点基础研究发展规划(973)项目 (2014CB046404)，国家自然科学基金(51305398)，浙江省自然科学基金（LQ13E050013），浙江省教育厅项目(Y201329543)资助

Fretting Characteristics of the Rubber O-Ring for a Mechanical Seal

ZHENG Jinpeng，SHEN Mingxue，MENG Xiangkai，LI Gan，PENG Xudong

（Engineering Research Center of Process Equipment and Its Remanufacture of the Ministry of Education, Zhejiang University of Technology, Hangzhou 310032, China）

Received:2013-10-06

摘要/Abstract

摘要：

采用含高阶项的 Mooney-Rivlin 本构模型对机械密封用O形丁腈橡胶圈进行了轴对称有限元分析，重点考察了位移幅值、介质压力、压缩率及摩擦系数对其微动特性的影响.结果表明：随着位移幅值的增加，O形圈在微动界面上可呈现黏着、混合黏滑和完全滑移3种不同的接触状态；介质压力、压缩率及摩擦系数对O形圈的微动运行行为有重要影响；混合黏滑状态下O形圈密封界面摩擦力的显著波动会影响浮动环的浮动性；滑移状态下O形圈伴随着较高的Von Mises应力易导致其发生剪切破坏、表面磨损加剧；而在黏着状态下O形圈的综合性能最佳.因此，应避免O形圈运行于混合黏滑状态，压缩率取10%左右，并降低摩擦系数，以减缓其表面磨损和剪切破坏并满足补偿环浮动性和追随性.

关键词: 机械密封, O形橡胶圈, 微动摩擦学, 黏滑特性, 运行行为

Abstract:

The fretting characteristics of the nitrile rubber O-ring for a mechanical seal were successfully simulated by axisymmetric finite element analysis, using the MooneyRivlin model with highorder terms. The effects of the displacement amplitude, medium pressure, precompression ratio and friction coefficient were investigated. The results show that three contact states for the fretting characteristics of rubber O-ring can be determined, i.e. stick state, mixed stickslip state and slip state with the increase of the displacement amplitude．The fretting running behavior of rubber Oring was strongly dependent upon the medium pressure, precompression ratio and friction coefficient. In mixed stick-slip state, the strong fluctuations of frictional force on the sealing interface would weaken the floatability of floating ring. In slip state, the high Von Mises stress may lead to shear failure and severe surface wear. However, Oring possessed the optimum comprehensive performance when working in stick condition. In a word, to mitigate shear failure and surface wear of Oring and meet the floatability and tracking property of the seal ring, the mixed stickslip state should be avoided and a compression of appoximately 10% and a lower coefficient would be preferred.

Key words: stickslip characteristic, running behaviors, mechanical seal, rubber O-ring, fretting tribology

中图分类号:

TB 42

郑金鹏，沈明学，孟祥铠，厉淦，彭旭东. 机械密封用O形橡胶密封圈微动特性[J]. 上海交通大学学报（自然版）, 2014, 48(06): 856-862.

ZHENG Jinpeng，SHEN Mingxue，MENG Xiangkai，LI Gan，PENG Xudong. Fretting Characteristics of the Rubber O-Ring for a Mechanical Seal[J]. Journal of Shanghai Jiaotong University, 2014, 48(06): 856-862.

参考文献

［1］顾永泉. 机械密封实用技术［M］. 北京: 机械工业出版社, 2001.

［2］LIAO Chuanjun, SUO Shuangfu, WANG Yuming, et al. Study on stickslip friction of reciprocating Oring using acoustic emission techniques［J］. Tribology Transactions, 2012, 55(1): 4351

［3］Erwan G, Isabelle P D. Thermoelastohydrodynamic modeling of hydrostatic seals in reactor coolant pumps ［J］. Tribology Transactions, 2007, 50(4): 466476.

［4］刘莹, 垚陈, 高志, 等. 三元乙丙密封材料不同工况下的摩擦性能［J］. 摩擦学学报, 2010, 30(5): 461465.

LIU Ying, CHEN Yao, GAO Zhi, et al. Friction performance of EPDM used for seals in different working conditions［J］. Tribology, 2010, 30(5): 461465.

［5］Darling S. Main coolant pump seal maintenance guide［M］. USA: Electric Power Research Institute, 1993.

［6］Blasiak S, Laski P A, Takosoglu J E. Parametric analysis of heat transfer in noncontacting face seals［J］. International Journal of Heat and Mass Transfer, 2013, 57(1): 2231.

［7］Fribourg D, Audrain A, Cougnon L. The performance of mechanical seals used in a high vibration environment ［J］. Sealing Technology, 2010, 2: 711.

［8］陈志, 高钰, 董蓉, 等. 机械密封橡胶O形圈密封性能的有限元分析［J］. 四川大学学报：工程科学版, 2011, 43(5): 234239.

CHEN Zhi, GAO Yu, DONG Rong, et al. Finite element analysis of sealing characteristics of the rubber Oring for a mechanical seal［J］. Journal of Sichuan University： Eengineering Science Edition, 2011, 43(5): 234239.

［9］Nam J H, Hawong J S, Shin D C, et al. A study on the behaviors and stresses of Oring under uniform squeeze rates and internal pressure by transparent type photoelastic experiment［J］. Journal of Mechanical Science and Technology, 2011, 25(9): 24272438.

［10］吴琼, 索双富, 刘向锋, 等. 丁腈橡胶O形圈的静密封及微动密封特性［J］. 润滑与密封, 2012, 37(11): 511.

WU Qiong, SUO Shuangfu, LIU Xiangfeng, et al. Static sealing and pseudosealing characteristics of nitrile rubber Oring ［J］. Lubrication Engineering, 2012, 37(11): 511.

［11］Tasora A, Prati E, Marin T. A method for the characterization of static elastomeric lip seal deformation ［J］. Tribology International, 2013, 60: 119126.

[1]	孔亚彬，沈明学，张执南，孟祥铠，彭旭东. 橡胶O形圈/不锈钢配副往复摩擦生热特性[J]. 上海交通大学学报, 2019, 53(11): 1352-1358.
[2]	杨笑，彭旭东，孟祥铠，王玉明. 端面倾斜对粗糙表面机械密封性能的影响[J]. 上海交通大学学报（自然版）, 2017, 51(6): 748-755.
[3]	程香平，彭旭东，孟祥铠. 菱形孔密封环端面密封性能分析[J]. 上海交通大学学报（自然版）, 2014, 48(1): 33-38.
[4]	彭旭东,于明彬，孟祥铠，白少先，盛颂恩,. 端面磨损对U型槽动压机械密封性能的影响 [J]. 上海交通大学学报（自然版）, 2010, 44(12): 1721-1726.